AGCO GSI 40 Series Скачать руководство пользователя страница 84

Страница: 84 / 164

Chapter 8: Roof Assembly

Attaching the Eave Angle to the Sidewall Sheet

The eave angle secures the bottom of the roof panels to the bin eave.

What You Should Know

Eave angles are bolted to the

outside

surface of the sidewall and will overlap each section.

1. Locate the top inside stiffener (B) and align the holes of the first eave angle (A) to the sidewall sheet

with the holes of the top inside stiffener (B).

IMPORTANT:

Make sure to align the center of the eave angle tab (C) a distance of

9.375 in

. from

the center of the top inside stiffener when assembling to the sidewall sheet. This is
very important to ensure the roof panels align properly with the rafters.

Figure 8-3

Eave angle alignment

First Eave angle (CTR-0720)

Eave angle tab

Top inside stiffener

2. Install flange bolts (D) and flange nuts (B), leaving the end holes open.

NOTE:

The quantity of flange bolts (D) and flange nuts (B) may vary, depending on the sidewall
punch pattern.

3. Install the second eave angle (C) overlapping the first eave angle (A).

4. Install the flange bolts (D) and flange nuts (B), leaving the last hole open for the next eave angle to

be installed.

NOTE:

The quantity of flange bolts (D) and flange nuts (B) may vary, depending on the sidewall
punch pattern.

5. Bend the eave angle tabs (G) upward to conform with each roof panel rib.

Pneg-4460A

60 Ft Diameter 40-Series Bins

Содержание GSI 40 Series





































































































































































Результаты поиска

Содержание GSI 40 Series

Отзывы:

AGCO GSI 40 Series, Руководство по монтажу, Страница: 84 / 164

Результаты поиска

Содержание GSI 40 Series

Отзывы: