manualshive.com logo in svg

Ag Leader OnTrac3 MDU-G4, Руководство по установке

Поделиться
Скачать
Ag Leader OnTrac3 MDU-G4 Скачать руководство пользователя страница 3

1   

T

ABLE

 

OF

 C

ONTENT

S

Table of Contents

MDU-G4

Introduction...............................................................................................................3
Legal Disclaimer .......................................................................................................3
Safety Information ....................................................................................................4

Safety Instructions...............................................................................................4
Warning Alerts.....................................................................................................5
Caution Alerts......................................................................................................6

Installation Requirements .........................................................................................6

Standard Tool Requirements ..............................................................................6
Vehicle Requirements .........................................................................................6

Technical Support.....................................................................................................7
Vehicle Inspection ....................................................................................................7

Components

Supported Models ....................................................................................................8
OnTrac3 Main Hardware Kit .....................................................................................8
MDU-G4 Switch Kit...................................................................................................8

OnTrac3 Installation

MDU-G4 Installation Procedure..............................................................................10

Install the Main Gear on the Steering Wheel ....................................................10

Examine Steering Column and Steering wheel ...........................................11

Install Spacer (If Needed).......................................................................12

Install the Top Ring......................................................................................12
Attach the Anti-Rotation Pin.........................................................................14
Install the MDU-G4 ......................................................................................15

Universal Bracket Installation .................................................................................16
Universal Bracket Installation Kit Overview ............................................................16
Universal Bracket Installation Procedure................................................................17
ECU-S1 Installation ................................................................................................19

ECU-S1 Orientation ..........................................................................................19

ECU-S1 Installation Procedure...............................................................................19

Cable Harness Installation

Cable Harness Connections Overview...................................................................21
Cable Harness Installation Procedure ....................................................................22
On/Off Switch .........................................................................................................23
Care and Maintenance ...........................................................................................23

Содержание OnTrac3 MDU-G4



























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды