manualshive.com logo in svg

Afar NX-2E1, Руководство оператора

Поделиться
Скачать
Afar NX-2E1 Скачать руководство пользователя страница 7

NetCrossing Gateway NX-2E1/T1 Operator’s Manual

iii -

FCC Notice

This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules.  These limits are designed to
provide reasonable protection against harmful interference in a residential
installation.  This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications.  However, there is no guarantee that
interference will not occur in a particular installation.  If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.

•

Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved in writing by AFAR
Communications Inc. may void the user’s authority to operate this equipment.  AFAR
Communications Inc. can not accept any financial or other responsibilities that may
be the result of your use of this information, including direct, indirect, special, or
consequential damages.  Refer to warranty documents for product warranty
coverage and specifics.

Содержание NX-2E1












































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды