manualshive.com logo in svg

Afar NX-2E1, Руководство оператора

Поделиться
Скачать
Afar NX-2E1 Скачать руководство пользователя страница 47

NetCrossing Gateway NX-2E1/T1 Operator’s Manual

4-13

ip-configuration

address=<ip address>
netmask=<string>
gateway=<ip address>

This command configures the gateway IP address, netmask and gateway.  The IP configuration
is optional and the gateways are shipped with these parameters left blank.  Once the IP
configuration has been initialized, the gateways will reply to “ping” packets.  The IP
configuration is also required in order to use the “ping”, “snmp” and “telnet” features.

Example:

> 

ipconfig add=207.154.90.81 netmask=255.255.255.0  gateway=207.154.90.2

ping

destination=<string>
count=0..500
size-bytes=32..1400

This command causes the gateway to “ping” the destination address and display the results.
The “ping” packet consists of an ICMP packet with a length specified by the “size-bytes”
parameter.  The destination is any valid IP address.  When the destination host receives the
packet it generates a reply of the same size.  Upon receiving the reply the gateway displays the
round trip delay.  This process is repeated until the number of replies reaches the value
specified by the “count” parameter (default to 4).  A count of zero leaves ping running
indefinitely until stopped by the user.

Example:

> 

ping  207.154.90.81  count=10  size=100

snmp

The gateway runs an SNMP agent which allows up to four IP addresses to be specified as valid
SNMP managers.  This command configures those IP addresses and the type of access allowed.
You can issue the command up to four times to specify each separate IP address manager.  The
gateways are shipped with all entries blank.  While no entries are specified, the unit accepts
SNMP “get” requests from any IP address with the “public” community.  Once one or more
entries are specified, the gateway only responds to requests from the specific IP addresses listed.
This list of authorized managers is also used for validating Telnet requests.

Refer to section 6 for an overview of Network Management using SNMP and Telnet.

manager=<ip address>

Specifies one valid IP address where the SNMP manager or Telnet session will run.

Содержание NX-2E1












































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды