Afag CS 16/30 Скачать руководство пользователя

Страница: 36 / 49

CS 16 - CS 20 - OI-vers. 5.3 gb. 20190312

3.3.5 Changing the ZA catch

The action direction of the ZA catch can be easily changed over; this should be done before the CS module is
mounted.

You must decide when the ZA intermediate stop should be activated: during extension or retraction?

The basic position at the ZA intermediate stop is designed for retracting the CS module. If you want to use the ZA
intermediate stop for extension, then the ZA catch must be changed over. This procedure is shown in the
following pictures.

Caution

The module or the station must not be pressurised when the ZA intermediate stop is
fitted to an installed CS module!

Installed CS modules should be removed when catches are to be changed over in
order to prevent squeezing of limbs by movable parts.

Содержание CS 16/30


















































Результаты поиска

Содержание CS 16/30

Отзывы:

Похожие инструкции для CS 16/30

Бренды по названию

Популярные бренды

Afag CS 16/30, Руководство пользователя

Результаты поиска

Содержание CS 16/30

Отзывы:

Похожие инструкции для CS 16/30

Бренды по названию

Популярные бренды