Afag 50195031 Скачать руководство пользователя | Manualshive

Страница: 21 / 27

background image

R02.1

07/01/2021

Page 21

Statusdisplay

– Input and Output

(Just in display mode 1. Parameter

– Dot in the second LED is off / Signal level are

inverted as soon as F1 is programmed as S)

Feeder runs.

Feeder off.

There is no signal at the sensor input. Signal level LO
is further processed.

There is no signal at the sensor input. Signal level LO
is further processed.

There is signal at the sensor input. Signal level HI is
further processed.

Feeder runs. Signal level LO is further processed.

Feeder off. Signal level LO is further processed.

Feeder off. Signal level HI is forward processed.

Feeder runs.

Feeder off.

«
...
19
20
21
22
23
...
»

Содержание 50195031




























Отзывы:

Нет отзывов

Похожие инструкции для 50195031

Бренд: ABB Страницы: 139

Бренд: ABB Страницы: 28

Бренд: ABB Страницы: 59

Бренд: ABB Страницы: 2

Бренд: GBD Страницы: 12

Бренд: XBOX Страницы: 4

Бренд: Panasonic Страницы: 72

Бренд: Panasonic Страницы: 45

Бренд: Panasonic Страницы: 24

Бренд: Valor Страницы: 20

Бренд: Taie Страницы: 28

Бренд: Samson Страницы: 48

Бренд: Kärcher Страницы: 4

Бренд: Rain Bird Страницы: 24

ESP-LXIVM Series

Бренд: Rain Bird Страницы: 16

Бренд: Rabe Страницы: 61

Бренд: Racal Instruments Страницы: 35

Бренд: Sunnen Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды