6
(2) Aluminum anti-rotation dowels - installed pre-
drilled hole for cotter pin installation
(11) pin point hinges installed (
glued
) Read to fly
(2) Aileron servo pull strings installed
Horizontal Stabilizer with elevator assembly
—covered
(14) seven per elevator, pin point hinges (
glued
)
- Ready
to
fly
Elevators
Pre-drilled
for the mounting of the
control
horns
Rudder
with (9) pin point hinges (
not glued
) – covered
Rudder Pre-drilled for the mounting of the
hinges, control horns and tail wheel steering arm.
SUB ASSEMBLIES:
#1:
(1) Fiberglass Cowling- painted - top and bottom - with
pre cut hot air exit slots and front engine baffling
installed.
(2) 4-40 x 25mm hex bolts for mounting inside center
section of cowl to fuse
(4) 4-40 x 20mm hex bolts for mounting inside top
section of cowl to fuse
(4) 4-40 x 16mm button head hex bolts for mounting
outside bottom section of cowl to fuse.
(10 ) #6 bonded washers for mounting cowling
(10) 3mm split lock washer for mounting cowling
#2:
(2)
Carbon
main landing gear, 1 left and 1 right
(2) 5 x 48mm Axle Bolts
(2) M8 lock nuts
(4) 5mm i.d. Wheel Collars with set-screws
(2) 115mm Dia. Main Wheels (Lite Type)
(4) 4-40x16mm hex style bolts for mounting wheel
pants
(4) 3mm flat washer for mounting wheel pants
(4) 3mm split ring lock washer for mounting wheel
pants
(8) 8-32x30mm hex head bolts for mounting main
landing
gear
(8) 4mm flat washers for mounting main landing gear
(8) 4mm split ring lock washers for mounting main
landing gear.
#3:
(2) Wheel Pants- Painted- pre mounted- 1 Left and 1
Right--
(4) 4-40 blind nuts installed in the wheel pants, 2 per
side.
#4:
(1) AW- Custom
Carbon
Tail Wheel Assembly
(1) Aluminum steering arm and mounting screws
(2) Steering springs
#5:
(1) 40mm O.D. x 1240mm
Carbon
wing tube
(1) 16mm O.D. x 220mm
Carbon
stab tube - Front
(1) 16mm O.D. x 460mm
Carbon
stab tube - Rear
(4) 8-32 x 30mm Hex head bolts for wing mounting
(4) #8 bonded washer for wing mounting
(4) 4mm split ring lock washers for wing mounting
(4) 4-40x16mm Hex style head bolts for stab mounting
(4) #6 bonded washer for stab mounting
(4) 3mm split ring lock washers for stab mounting
(4) 1.8mm cotter pins - Second method -wing mounting
for
security
#6:
(6) 4-40 3” Two end threaded pushrod with nuts for
ailerons
(4) 4-40 2 1/2” Two end threaded pushrod with nuts for
elevators
(2) 4-40x300mm One end threaded pushrod –Throttle
and
Choke
(2) 4-40 solder coupler - Throttle and Choke
(2) 4-40 Metal clevises - Throttle and Choke
(12) Brass spacers – 6 for ailerons; 4 for elevators; 1 for
throttle; 1 for choke
(22) 4-40 Ball Links – 12 for ailerons; 8 for elevators; 1
for throttle; 1 for choke
(22) 4-40 x 16mm hex style bolts
(22) 4-40 lock nuts
(12) Flat washer for top of ball links
(1) 500mm
Carbon tube
- pushrod reinforcement
#7:
(2) 1.2x1500mm plastic coated pull-pull steel cable.
(4) 4-40 Metal R/C links with nuts
(4) 3.5 x 5mm brass pull-pull swaging tubes
(12) AW double control horns
(72) T2.6 x 16mm Phillips head mounting screws
(4) 4-40 Ball Links - Rudder
(4) 4-40 x 16mm hex style bolts
(4) 4-40 lock nuts
(2) Brass spacer
(2) Flat washer for top of ball links
#8:
(1)
1500cc (50 ounce) Gas Fuel Tank assembly (Fuel)
(1) 1000cc (34 ounce) Gas Fuel Tank assembly (Smoke)
(1) 5ft. large gas fuel line
(4) Brass barbs for fuel line
#9:
(2) Throttle – Choke servo mounting plates
(4) Engine mounting templates
(DA150 –170, 3W150 - 157, ZDZ 160 and
ZDZ
J-160)
(2) pre cut balsa sheet for canister tunnel
(2) Pipe mounting brackets - Plywood
(8) 4-40 x 16mm hex head bolts—mount brackets
(8) 3mm flat washer
(8) 3mm split ring lock washer
(16) 11mm O.D. x 20mm silicon tubes – canister pipe
(6) Rubber grommets - fuel line guide
(1) Cowl template - cutting muffler stack exit holes
