6
(14) pin point hinges glued
(2) Aileron servo string installed
(2) Pilot holes pre drilled for control horns mounting
Horizontal Stabilizer –
1 Left 1 right with elevator as-
sembly with (10) pin point hinges (glued)---
covered
(2) Pilot holes pre drilled for control horns mounting
Rudder
with (7) pin point hinges (not glued) – covered
(2) Pilot holes pre drilled for control horns mounting
(1) Pilot holes predrilled for steering tiller
SUB ASSEMBLIES:
#1:
(1) Fiberglass Cowling—painted with (6) screws
holes
(6) 4-40x16mm hex style bolts for mounting of the
cowling
(6) #6 bonded washers for mounting of the cowling
(6)
Φ
3mm split ring lock washers for the mounting of
the cowling
(1) Plastic vacuumed fairing for center cabane
#2:
(1) 5mm 7075 Aluminum Main Landing Gear --
painted
(2) 5mm dia. X45mm AL Axle
(2) M8 lock nuts
(4) 5mm i.d. Wheel Collars with set-screws
(2) 85mm Dia. Main Wheels (Lite Type)
(4) 4-40x14mm hex style bolts for mounting wheel
pants
(4)
Φ
3mm flat washer for mounting wheel pants
(4)
Φ
3mm split ring lock washer for mounting wheel
pants
(4) 8-32x25mm hex head bolts for mounting main
landing gear
(4)
Φ
4mm flat washers for mounting main landing
gear
(4)
Φ
4mm split ring lock washer for mounting main
landing gear
#3:
(2)Wheel Pants—1 Left and 1 Right---Painted
(4) 4-40 blind nuts installed on the wheel pants, 2 per
side.
#4:
(1) AL Tail Wheel Assembly – Medium with solid
rubber wheel
#5:
(2) Outer struts – Left and Right, covered, marked
with BL, BR (Bottom Left, Bottom Right)
(8) 6-32x10mm hex head bolts for the Outer struts
mounting
(8) 6-32 lock nuts for the Outer struts mounting
(8) 2mm L steel Outer struts fittings
(8) 6-32x10mm hex head bolts for the L steel Outer
struts fittings
(2) 1/4x40mm Nylon Bolts for the bottom wing
mounting
#6:
(4) 4-40 3” left and right hand threaded pushrod with
nuts for ailerons
(2) 4-40 2.5” left and right hand threaded pushrod
with nuts for elevators.
(2) 4-40x300mm Threaded pushrod-Throttle/Choke
(2) 4-40 solder couplers
(8) Brass spacers – 4 for ailerons; 2 for elevators; 1
for throttle; 1 for choke
(8) 3mm flat washers – 4 for ailerons; 2 for elevators;
1 for throttle; 1 for choke
(14) 4-40 Ball Link – 8 for ailerons; 4 for elevators; 1
for throttle; 1 for choke
(14) 4-40x16mm hex style bolts
(14) 4-40 lock nuts
#7:
(2) 1x1000mm plastic coated pull-pull steel cable.
(4) 4-40 Metal R/C links with nuts
(4)
Φ
3.5x4mm brass pull-pull swaging tubes
(8) AL double control horns
(48) T2.6x12mm Phillips head mounting screws for
the control horns
(4) 4-40 Ball Links-Rudder
(4) 4-40x16mm hex style bolts
(4) 4-40 lock nuts
(2) Brass spacers
(2) 3mm flat washers
#8:
(1) 750cc Gas Fuel Tank assembly
(1) 450cc Smoke Tank assembly
(1) 4ft. large gas fuel line
(4) brass barbs for fuel tank
(2) Fuel filler dot - 1 male and 1 female
#9:
(2)Throttle servo mounting trays
(1) 4-sided throttle servo mounting tray
(2) Engine mounting template (DA, 3W)
(1) 140x70x6mm foam for the Fuel tank
(1) 160x70x6mm foam for the smoke tank
(2) 300x80x6mm sponge for the receiver and battery
(8) 8x450mm Nylon Ties for the fuel tank mounting
(10) 3x150mm Small Nylon ties for the fuel line
(4) 356x12.5mm Velcro straps
(1) paper degree meter for the rudder
(1) 12mm dia. aluminum insert
(6) Rubber Grommets - each 2 for
Φ
6mm,
Φ
8mm,
Φ
10mm-fuel line and wire guide
(1) Card Stock (8-1/2”x12”) for making of the tem-
plate for cutting of cowling
(1) Custom Throw Meter
