manualshive.com logo in svg

Aerotech Ensemble CP Series, Руководство по оборудованию

Поделиться
Скачать
Aerotech Ensemble CP Series Скачать руководство пользователя страница 12

Electrical Safety

Ensemble CP

Safety Procedures and Warnings

The following statements apply wherever the Warning or Danger symbol appears within this manual. Failure
to observe these precautions could result in serious injury to those individuals performing the procedures
and/or damage to the equipment.

N O T E :

Read this manual in its entirety before installing, operating, or servicing this product. If you do

not understand the information contained herein, contact an Aerotech representative before proceeding.
Strictly adhere to the statements given in this section and other handling, use, and operational information
given throughout the manual to avoid injury to you and damage to the equipment.

N O T E :

Aerotech continually improves its product offerings; listed options may be superseded at any

time. All drawings and illustrations are for reference only and were complete and accurate as of this
manual’s release. Refer to www.aerotech.com for the most up-to-date information.

D A N G E R : This product contains potentially lethal voltages. To reduce the possibility of
electrical shock, bodily injury, or death the following precautions must be followed.

1. Disconnect electrical power before servicing equipment.
2. Disconnect electrical power before performing any wiring.
3. Access to the Ensemble CP and component parts must be restricted while connected to a

power source.

4. To minimize the possibility of electrical shock and bodily injury, extreme care must be

exercised when any electrical circuits are in use. Suitable precautions and protection must
be provided to warn and prevent persons from making contact with live circuits.

5. Install the Ensemble CP inside a rack or enclosure.
6. The shunt resistor temperature can exceed 70°C during normal operation and contains

lethal voltage on its terminals and surface. It must be properly enclosed and shielded to
avoid risk of fire and operator shock.

7. Do not connect or disconnect any electrical components or connecting cables while

connected to a power source.

8. All components must be properly grounded in accordance with local electrical safety

requirements.

9. Operator safeguarding requirements must be addressed during final integration of the

product.

D A N G E R : The Ensemble CP case temperature may exceed 70°C in some applications.

www.aerotech.com

11

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание Ensemble CP Series























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды