Aerotech Automation1 XC4e Скачать руководство пользователя страница 52

Страница: 52 / 122

2.3.1.4. Encoder Phasing

Incorrect encoder polarity will cause the system to fault when enabled or when a move command is
issued.

illustrates the proper encoder phasing for clockwise motor rotation (or positive

forcer movement for linear motors). To verify, move the motor by hand in the CW (positive) direction
while observing the position of the encoder in the diagnostics display (see

Figure 2-24

For dual loop systems, the velocity feedback encoder is displayed in the diagnostic display (

Figure 2-24

Figure 2-23:

Encoder Phasing Reference Diagram (Standard)

IMPORTANT

: Encoder manufacturers may refer to the encoder signals as A, B, and Z. The

proper phase relationship between signals is shown in

Figure 2-23

Figure 2-24:

Position Feedback in the Diagnostic Display

2.3.1. Primary Encoder Inputs

XC4e Hardware Manual

www.aerotech.com

Содержание Automation1 XC4e



























































































































Результаты поиска

Содержание Automation1 XC4e

Отзывы:

Бренды по названию

Популярные бренды

Aerotech Automation1 XC4e, Руководство по оборудованию

Результаты поиска

Содержание Automation1 XC4e

Отзывы:

Бренды по названию

Популярные бренды