manualshive.com logo in svg

Aerotech Automation1 XC4e, Руководство по оборудованию

Поделиться
Скачать
Aerotech Automation1 XC4e Скачать руководство пользователя страница 107

Chapter 5: Maintenance

IMPORTANT

: For your own safety and for the safety of the equipment:

l

Do not remove the cover of the XC4e

l

Do not attempt to access the internal components.

A fuse that needs to be replaced indicates that there is a more serious problem with the
system or setup. Contact Global Technical Support for assistance.

DANGER

: If you must remove the covers and access any internal components be aware of

the risk of electric shock.

1. Disconnect the Mains power connection.
2. Wait at least ten (10) minutes after removing the power supply before doing main-

tenance or an inspection. Otherwise, there is the danger of electric shock.

3. All tests must be done by an approved service technician. Voltages inside the con-

troller and at the input and output power connections can kill you.

Table 5-1:

LED Description

LED

Color

Description

PWR

GREEN

The light will illuminate and remain illuminated while power is
applied.

EN/FLT

GREEN

The axis is Enabled.

RED

The axis is in a Fault Condition.

GREEN/RED 

(alternates)

The axis is Enabled in a Fault Condition.
or
The light is configured to blink for setup.

Table 5-2:

Troubleshooting

Symptom

Possible Cause and Solution

No Communication

Make sure the power LED is illuminated (this indicates that power is present).
Make sure that all communication cables (HyperWire, for example) are fully
inserted in their ports.

XC4e Hardware Manual

Chapter 5: Maintenance

www.aerotech.com

107

Содержание Automation1 XC4e



























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды