Aerotech Automation1 XC4e Скачать руководство пользователя страница 29

Страница: 29 / 122

2.1.2. Motor Supply Connector

Motor power is applied to the

AC1

and

AC2

terminals of the XC4e Motor Supply connector. The XC4e10

AC1

input is internally connected to a 5 A fuse. The XC4e20/30

AC1

input is internally connected to a 10

A fuse. Refer to

Table 5-4

for the internal fuse part numbers. The

AC2

input is not internally fused. An

external fuse is required if

AC2

is not connected to Neutral.

IMPORTANT

: Before you operate the XC4e, install a ground connection for your safety

and to prevent damage to the equipment.

For CE compliance, Aerotech recommends that you use an AC line filter. Connect the filter as close as
possible to the drive. For more information about the AC line filter, refer to

Section 2.1.4.

IMPORTANT

: Refer to local electrical safety requirements to correctly size external system

wires.

Figure 2-2:

Motor Supply Connections

Table 2-3:

Motor Supply Connector Wiring Specifications

Pin

Description

Recommended Wire Size

AC1

0-240 VAC Motor Power Input

0.5 mm

(#20 AWG)

AC2

Neutral (N) or 240 VAC Motor Power Input with external fuse

0.5 mm

(#20 AWG)

Protective Ground

0.5 mm

(#20 AWG)

Table 2-4:

Mating Connector Part Numbers for the Motor Supply Connector

Type

Aerotech

P/N

Third Part

P/N

Screw

Torque: Nm

Wire Size:

[AWG]

7-Pin Terminal Block

ECK02387

Phoenix 1756353

0.5 - 0.6

3.3 - 0.0516 [12-30]

XC4e Hardware Manual

2.1.2. Motor Supply Connector

www.aerotech.com

Содержание Automation1 XC4e



























































































































Результаты поиска

Содержание Automation1 XC4e

Отзывы:

Бренды по названию

Популярные бренды

Aerotech Automation1 XC4e, Руководство по оборудованию

Результаты поиска

Содержание Automation1 XC4e

Отзывы:

Бренды по названию

Популярные бренды