Aerotech Automation1 XC4e Скачать руководство пользователя страница 38

Страница: 38 / 122

2.2. Motor Power Output Connector

DANGER

: Before you do maintenance to the equipment, disconnect the electrical power.

Wait at least ten (10) minutes after removing the power supply before doing maintenance
or an inspection. Otherwise, there is the danger of electric shock.

The XC4e can be used to drive the following motor types:

Brushless (refer to

Section 2.2.1.

)

DC Brush (refer to

Section 2.2.2.

)

Stepper (refer to

Section 2.2.3.

)

For a complete list of electrical specifications, refer to

Section 1.1.

IMPORTANT

: Refer to local electrical safety requirements to correctly size external system

wires.

The 7-pin terminal block style motor output connector is located on the front panel. The pinout for this
connector is shown in

Table 2-7

Table 2-7:

Motor Power Output Connector Pinout

Pin

Description

Recommended

Wire Size

Connector

Earth Ground to Motor

1.3 mm

(#16 AWG)

Brushless Phase A Motor Lead
DC Brush +
Stepper

1.3 mm

(#16 AWG)

Brushless Phase B Motor Lead
Stepper

1.3 mm

(#16 AWG)

Brushless Phase C Motor Lead
DC Brush -
Stepper Return

1.3 mm

(#16 AWG)

Table 2-8:

Mating Connector Part Numbers for the Motor Power Output Connector

Type

Aerotech

P/N

Third Part

P/N

Screw

Torque: Nm

Wire Size:

[AWG]

7-Pin Terminal Block

ECK02387

Phoenix 1756353

0.5 - 0.6

3.3 - 0.0516 [12-30]

2.2. Motor Power Output Connector

XC4e Hardware Manual

www.aerotech.com

Содержание Automation1 XC4e



























































































































Результаты поиска

Содержание Automation1 XC4e

Отзывы:

Бренды по названию

Популярные бренды

Aerotech Automation1 XC4e, Руководство по оборудованию

Результаты поиска

Содержание Automation1 XC4e

Отзывы:

Бренды по названию

Популярные бренды