manualshive.com logo in svg

Aeroqual AQM 65, Руководство пользователя, Страница: 127 / 127

Поделиться
Скачать
Aeroqual AQM 65 Скачать руководство пользователя страница 127

 

MRK-D-0034 V2.0 

 

 

 Aeroqual AQM 65 User Guide    

 

Page | 126 

8  Copyright 

Copyright Aeroqual Limited. All rights reserved. Reproduction, transfer, distribution or storage of part 
or all of the contents of this document in any form without the prior written permission of Aeroqual 
Limited is prohibited.  
“Aeroqual” is a registered trademark of Aeroqual Limited. Other product and company names 
mentioned herein may also be trademarks or trade names.  

Aeroqual operates a policy of continuous development. Aeroqual reserves the right to make changes 
and improvements to any of the products described in this document without prior notice.  

Under no circumstances shall Aeroqual be responsible for any loss of data or income or any special, 
incidental, consequential or indirect damages howsoever caused.  

The contents of this document are provided "as is". Except as required by applicable law, no 
warranties of any kind, either express or implied, including, but not limited to, the implied warranties of 
merchantability and fitness for a particular purpose, are made in relation to the accuracy, reliability or 
contents of this document.  

Aeroqual reserves the right to revise this document or withdraw it at any time without prior notice. The 
availability of particular products may vary by region. Please check with the Aeroqual dealer nearest 
to you. 

 

9  Compliance  

1. The Aeroqual AQM 65 Monitor complies with EN 61000-6-1:2001  

2. The Aeroqual AQM 65 Monitor complies with EN 61000-6-3:2001  

3. The Aeroqual AQM 65 Monitor complies with Part 15 of the FCC Rules. Operation is subject to the 
following two conditions: (1) these devices may not cause harmful interference, and (2) these devices 
must accept any interference received, including interference that may cause undesired operation. 

 

NOTE:

  This equipment has been tested and found to comply with the limits for a Class B digital 

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide 
reasonable protection against harmful interference in a residential installation. This equipment 
generates, uses and can radiate radio frequency energy and, if not installed and used in 
accordance with the instructions, may cause harmful interference to radio communications. 
However, there is no guarantee that interference will not occur in a particular installation. If 
this equipment does cause harmful interference to radio or television reception, which can be 
determined by turning the equipment off and on, the user is encouraged to try to correct the 
interference by one or more of the following measures: 

 

Reorient or relocate the receiving antenna. 

 

Increase the separation between the equipment and receiver.  

 

Connect the equipment into an outlet on a circuit different from that to which the receiver 
is connected. 

 

Consult the dealer or an experienced radio/TV technician for help. 

 

 

 

 

 

 

 

 

 

Содержание AQM 65
































































































































Отзывы:

Нет отзывов