background image

These devices are intended for indoor use only.

Do not install the device in an environment where the operating ambient 
temperature might exceed the recommended ranges.

For products available in the USA/Canada market, for the 2.4 GHz band, only 

channels 1-11 can be operated. Selection of other channels is not possible.

Changes or modifications made to this device that are not expressly approved
by the party responsible for compliance could void the user's authority to 

operate the equipment.

Use only attachments and accessories specified by Aerohive.

These devices are not intended for use by persons (including children) with 
reduced physical, sensory, or mental capabilities, or with lack of experience of

knowledge unless they are given supervision or instruction concerning use of th

devices by a person who is responsible for their safety. Children should be 

supervised to ensure that they do not play with the devices.

Electrostatic discharge (ESD) can damage equipment and impair electrical 

circuitry. ESD damage occurs when electronic components are improperly 

handled and can result in complete or intermittent failures. Be sure to follow ES

prevention procedures when handling electronic components and equipmen

During operation, the surfaces of the AP122 can become hot. Use caution whe

handling.

To meet federal radiation exposure requirements, these devices should be 

installed at a minimum distance of 7.8" (20 cm) from people or animals.

Install the AP

You can mount the AP122 on a flat surface or wall, or on the rails of a standard dropped ceiling grid 

using the hardware on the back of the chassis. 

The following sections describe how to install your AP122 devices and connect them to the network. 

Shipping Carton Contents

The AP122 access point shipping carton contains the following items:

• AP122 chassis
• Generic QuickStart Guide
• 3 wall-mount screws with anchors

Page 8 of 14

AP122 Hardware User Guide

11/14/2016

Содержание AP122















Отзывы: