AeroClave RDS 3110 Скачать руководство пользователя страница 27

Страница: 27 / 35

AeroClave

RDS 3110 Operator Manual

Released July 1, 2020

Page 27

Use or disclosure of data contained on this sheet is subject to the restriction on the cover page of this User’s Manual.

Section 5: Fire Fighting Measures

Flammable Properties: Flash Point:

Not Available (Non Flammable)

Flammable Limits: Lower Flammable Limit:

Not Established

Burn Rate:

Unknown

Upper Flammable Limit:

Not Established

Flammability Classification:

Non

Flammable liquid

Autoignition Temperature:

Not Established

Hazardous Combustion Products:

Thermal or other decomposition may yield chlorine dioxide or chlorine.

Extinguishing Media:

N/A (Non

Flammable liquid)

Additional Considerations:

None

FIRE FIGHTING INSTRUCTIONS:

Non

Flammable liquid

NFPA Rating: Health:

Flammability:

Reactivity:

PPE:

NONE

Section 6: Accidental Release Measures

Spill Clean Up

No special cleanup measures are required for the consumer product. To avoid the possibility of “bleaching” the spill should be absorbed

with paper towels, and the area rinsed with clean water.

Accidental Release Measures

Spills are slippery and should be cleaned up promptly.

Section 7: Handling and Storage

Handling:

Keep away from heat and strong acids. Do not ingest. Keep container closed. Use only with adequate ventilation.

Storage:

Keep container tightly closed and sealed until ready for use. Keep container in a well

ventilated place. Do not store above

120

F or near fire of open flame. Store large quantities in buildings to comply with OSHA 1910.106. Do not transfer contents to bottles

or other unlabeled containers. Do not reuse empty containers. Keep out of reach of children.

Incompatible materials:

Strong acids

Special Packaging Materials:

None

Section 8: Exposure Control/ Personal Protection

Engineering Controls:

Use in adequately ventilated areas.

Personal Protective Equipment:

Eye/Face Protection:

Not required for consumer product.

Skin Protection:

Not required for consumer product.

Respirators:

None required for normal use. If consumer product accidentally contacts strong acids in restricted ventilation area,

avoid breathing the vapors, and allow adequate time for the vapors to disperse before re

entering the restricted area.

Exposure Limits:

Oxychlorine Compounds: n

Alkyl Dimethyl Ethyl benzyl Ammonium Chloride:

PEL (OSHA): Not available PEL (OSHA): Not available

TLV (ACGIH): Not available TLV (ACGIH): Not available

Alkyl Dimethyl Benzyl Ammonium Chloride:

PEL (OSHA): Not available

TLV (ACGIH): Not available

Section 9: Physical and Chemical Properties

Appearance:

Colorless liquid

Odor:

Mild

Fresh

Physical State:

Liquid

pH:

Boiling Point (°F):

212

Solubility in Water:

100%

Freezing Point (°F):

Vapor Pressure (mm Hg):

Not Available

Volatile Organic Compounds (VOC):

None

Evaporation Rate:

Less than Ether

Specific Gravity:

1.003 @ 68°F (20°C)

Density (lb./gal):

8.40 @ 68°F (20°C)

Section 10: Stability and Reactivity

Chemical Stability:

The product is stable.

Incompatibility with other Materials:

Strong acids

Conditions to avoid:

Contact with strong acids

Hazardous Polymerization:

Will not occur.

Hazardous Decomposition Products:

Thermal or other decomposition may yield chlorine dioxide or chlorine.

Содержание RDS 3110




































Результаты поиска

Содержание RDS 3110

Отзывы:

Бренды по названию

Популярные бренды

AeroClave RDS 3110, Руководство оператора

Результаты поиска

Содержание RDS 3110

Отзывы:

Бренды по названию

Популярные бренды