AEQ FORUM LITE Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 135

AEQ FORUM LITE Скачать руководство пользователя страница 32

AEQ

FORUM

LITE

Ultra-compact digital audio mixer

32

In  order  to  make  installation  process  easier,  AEQ  offers  specific  pre-fabricated  cable  kits  for
AEQ FORUM  LITE audio input/output, both analog and digital,  as  well  as studio headphones:
FR  CAB  INP,  consisting  in  a  male  DB15  connector  soldered  to  4  balanced  and  shielded  6
meters long paired cables with no connectors at the other end, for 4 inputs or outputs. For more
information please check section 2.2.5 of this manual.

AEQ can upon request provide fully finished cables and in special lengths. For more information
please refer to AEQ sales department or authorised distributors.

-

Programming digital outputs as S/PDIF.

In  order  to  provide  outputs  to  S/PDIF  equipments,  the  programming  procedure
described  below  adapts  the  levels  and  unbalances  the  signals  by  joining  OUT1-  ,
OUT2-,  OUT3-,  and  OUT4-  to  their  corresponding  GND,  so  the  signal  is  taken  from
each OUT+ to OUT– (or GND).

Start by following the steps detailed at section 2.2.3.1 (it's

VERY IMPORTANT

to turn

first the equipment off and disconnect the power supply cable). Then, at the "DIGITAL
INPUTS AND OUTPUTS PROGRAMMING ZONE", you can change the outputs one by
one from AES/EBU to S/PDIF by moving the 4 jumpers associated with each output
from position 1-2 (up) to position 2-3 (down), as shown in the following image:

IMPORTANT NOTE:

Regarding the wiring, the chassis of microphones must be connected to

the chassis of the console frame in order to protect the microphone inputs against uncontrolled
static shocks. Pin 1 (Ground) must be connected to the metal case of XLR connector in the
available terminal for this purpose, so any static shock will be downloaded to ground through
the frame chassis. This rule must be followed in every connector throughout the cable in case of
connections by means of aerial connectors. In the same way, for AES3 or USB digital signals,
the chassis of PCs or other digital audio devices must be also connected to the chassis of the
console frame.

Digital output 4

Digital output 3

Digital output 2 Digital output 1

Jumpers J49, J56,

Jumpers J31, J38,

Jumpers J45, J52, Jumpers J28, J34,

J57 and J58

J39 and J40

J53 and J54

J35 and J36

Position 1-2: AES/EBU
Position 2-3: S/PDIF

«
...
30
31
32
33
34
...
»

Содержание FORUM LITE








































































































































Отзывы:

Нет отзывов