manualshive.com logo in svg

AEQ FORUM LITE, Руководство пользователя, Страница: 23 / 135

Поделиться
Скачать
AEQ FORUM LITE Скачать руководство пользователя страница 23

 

 

AEQ

 

FORUM

 LITE

 

Ultra-compact digital audio mixer 

 

23 

 

 
IMPORTANT  NOTE:  Do  not  connect  this  output  to  any  device  but  the  control  and 
monitoring  module 

(there  is  a  severe  risk  of  damage  to  other  equipment  or  even  the  audio 

engine itself). In order to avoid any damage to the unit is 

VERY IMPORTANT 

to turn off the unit 

before connecting or disconnecting this cable. 
 
The  audio  output  for 

CUE

  or  prelisten  is  also  located  in  this  area.  See  section  2.2.2.4  in  this 

manual. 

 

2.2.2. Auxiliary connections. 

 
This area of the AEQ FORUM LITE back panel includes a  wide  variety  of inputs and  outputs, 
required  to  integrate  the  unit  with  any  professional  audio  installation,  including  several 
headphone  and  external  speaker  outputs,  general  purpose  inputs  and  outputs,  control  and 
studio speakers. 
 
Among these auxiliary console inputs and outputs, you can find not only analog signals such as 
headphones,  speakers  or  CUE,  but  also  physical  general  purpose  inputs  and  outputs  GPIOs 
(both open-collector and relay switched), virtual GPIOs over IP network, and finally the control 
and configuration interfaces with an external computer running the associated setup and remote 
control software. 

 

2.2.2.1. GPIO. 

 
AEQ FORUM LITE includes many general purpose inputs and outputs using optocouplers and 
relay contacts, all of them made available at the back panel of the audio engine. 
 

2.2.2.1.1. Opto-coupled GPI.  

 

 
AEQ FORUM LITE includes 8 electronic input interfaces of opto-coupled or open collector type - 
GPIs - through the female DB15 connector labelled "

GP INPUTS

". 

 
Specifications: 

 

•

 

Opto-coupler protected inputs (TLP127). 

•

 

Maximum Input Current: 50mA. 

•

 

Applicable voltage: from 5V to 24V. 

 

 

Associated electronic with opto-coupled GPI  

 

In  order  to  make  installation  process  easier,  AEQ  offers  specific  pre-fabricated  cable  kits  for 
AEQ  FORUM  LITE  data  input/output  within  the  optional  modules  range:  CP  CAB  GPIO, 
consisting in  a male DB15 connector soldered to a  6 meters long cable  with no connectors at 
the other end. For more information please check section 2.2.5 of this manual.

 

 

 

Содержание FORUM LITE








































































































































Отзывы:

Нет отзывов