background image

11

11

If needed, an exploded view of the product can be ordered. Please 

state the Article No. as well as the machine type printed on the label 

and order the drawing at your local service agents or directly at: 

Techtronic Industries Australia Pty Ltd

PO Box 1065 

Mount Waverley VIC 3149 

Tel. no. 1300 234 797 

Australia

Techtronic Industries N.Z. Limited

PO Box 12-806 

Penrose AUCKLAND 1642 

Tel. no. 0800 234 797 (0800 AEGPWR) 

New Zealand

SYMBOLS

Safety alert

Please read the instructions carefully before starting 

the machine.

Always wear goggles when using the machine.

Wear ear protectors.

Regulatory Compliance Mark (RCM). Product meets 

applicable regulatory requirements.

Indoor use

Wet condition alert. Do not expose to rain. Store 

indoors.

Risk of breathing. Air obtained directly from the air 

compressor should never be used to supply air for 

human consumption.

Risk of bursting. Do not adjust regulator to result 

in output pressure greater than marked maximum 

pressure of attachment. Do not use at pressure 

greater than 8 bar (116 psi).

Hot surface: To reduce the risk of injury or damage, 

avoid contact with any surface.

This compressor may start without warning.

Risk of fire or explosion.

 Spray area must be well 

ventilated. Do not smoke while spraying or spray 

where spark or flame is present. Keep compressors 

as far from the spraying area as possible. Keep 

compressor, at least 10 m from the spraying area 

and all explosive vapours.

Caution, risk of electric shock

Do not dispose of electric tools together with 

household waste material. Electric tools and 

electronic equipment that have reached the end of 

their life must be collected separately and returned 

to an environmentally compatible recycling facility.

Содержание AC30100S

















Отзывы: