Advantech PCE-7214 Скачать руководство пользователя | Manualshive

Страница: 52 / 90

background image

PCE-7214 User Manual

42

4.1

Before you Begin

To facilitate the installation of the enhanced display drivers and utility software, read
the instructions in this chapter carefully. The drivers for the PCE-7214 are located on
the software installation CD. The Intel Chipset Software Installation Utility is not
required on any systems running Windows NT 4.0. Updates are provided via Service
Packs from Microsoft.

Before you begin, it is important to note that most display drivers need to have the
relevant software application already installed in the system prior to installing the
enhanced display drivers. In addition, many of the installation procedures assume
that you are familiar with both the relevant software applications and operating sys-
tem commands. Review the relevant operating system commands and the pertinent
sections of your application software's user manual before performing the installation.

4.2

Introduction

The Intel Chipset Software Installation (CSI) utility installs the Windows INF files that
outline to the operating system how the chipset components will be configured. This
is needed for the proper functioning of the following features:



Core PCI and ISAPNP Services



PCIe Support



SATA Storage Support



USB Support



Identification of Intel

®

Chipset Components in the Device Manager

Note!

The files on the software installation CD are compressed. Do not
attempt to install the drivers by copying the files manually. You must use
the supplied SETUP program to install the drivers.

Note!

One of the following operating systems must be fully installed and run-
ning on the system before installing this software:
1. Microsoft Windows* Server 2003
2. Microsoft Windows Server 2003 x64 Edition*
3. Microsoft Windows XP Professional x64 Edition*
4. Microsoft Windows XP
5. Microsoft Windows 2000
6. Microsoft windows Vista

«
...
50
51
52
53
54
...
»

Содержание PCE-7214



























































































Отзывы:

Нет отзывов

Похожие инструкции для PCE-7214

Бренд: EAW Страницы: 10

Бренд: Lab.gruppen Страницы: 35

Бренд: Yamaha Страницы: 6

Бренд: Yamaha Страницы: 4

Бренд: Yamaha Страницы: 22

Бренд: Yamaha Страницы: 49

SABVISION NVR32

Бренд: SAB Страницы: 29

Бренд: ICOP Technology Страницы: 34

Бренд: Comtrend Corporation Страницы: 4

Бренд: AC Infinity Страницы: 24

Бренд: Sony Ericsson Страницы: 93

i.MX 8M Mini LPDDR4 EVK

Бренд: NXP Semiconductors Страницы: 20

Бренд: ZALMAN Страницы: 9

Бренд: Roland Страницы: 224

Бренд: Xilinx Страницы: 36

Бренд: Enterasys Страницы: 5

Бренд: JCAT Страницы: 2

Бренд: b&t Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды