manualshive.com logo in svg

Advantech PCE-7214, Руководство пользователя

Поделиться
Скачать
Advantech PCE-7214 Скачать руководство пользователя страница 6

PCE-7214 User Manual

vi

Verified CPU List

Verified Memory List

Certification and Safety Instructions

This device complies with the requirements in part 15 of the FCC rules: Operation is
subject to the following two conditions:

1.

This device may not cause harmful interference, and

2.

This device must accept any interference received, including interference that 
may cause undesired operation

This equipment has been tested and found to comply with the limits for a Class A dig-
ital device, pursuant to Part 15 of the FCC Rules. These limits are designed to pro-
vide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Opera-
tion of this device in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his/her own expense. The
user is advised that any equipment changes or modifications not expressly approved
by the party responsible for compliance would void the compliance to FCC regula-
tions and therefore, the user's authority to operate the equipment. 

CPU Family

sSpec.

Core 
Stepping

Power

Vcore

FSB

Mfg. Tech HT

L2 cache

XEON-2.33 G (5148) SLABH

B2

40W

1.150V-1.250V 1333

65nm

Y

4MB

XEON-2 G (5130)

SLAGC

G0

65W

1.275V

1333

65nm

Y

4MB

XEON-2 G (5405)

SLAP2

C0

80W

0.95V - 1.225V 1333

45nm

Y

12MB

XEON-1.60 G(5310)

SL9XR

B3

80W

1.325V max

1066

65nm

Y

8MB

Brand

Size

Speed

Type

ECC Vendor PN

Memory 

Transcend
RoHS)

2GB

DDR2 533 Register DDR2 Y

TS256MQR72V5U

Micron 7WE17 D9HNL

1GB

DDR2 667 Register DDR2 Y

TS128MQR72V6J

ELPIDA E5108AG-6E-E

2GB

DDR2 667 Register DDR2 Y

TS256MQR72V6U

SAMSUNG K4T1G084QA

4GB

DDR2 667 Register DDR2 Y

TS512MQR72V6T

ELPIDA E1104AOSE-6E-E

Caution!

There is a danger of a new battery exploding if it is incorrectly installed. 
Do not attempt to recharge, force open, or heat the battery. Replace the 
battery only with the same or equivalent type recommended by the man-
ufacturer. Discard used batteries according to the manufacturer's 
instructions.

Содержание PCE-7214



























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды