Advantech EKI-7659CPI Скачать руководство пользователя | Manualshive

Страница: 94 / 101

background image

EKI-7659CPI_Manual_ed33 84

Chapter 4

Troubleshooting

Verify that is using the right power cord/adapter (+12~48V

DC

), please don’t use the

power  adaptor  with  DC  output  voltage  higher  than  48  V,  or  it  will  burn  this  converter
down.

Select the proper UTP cable to construct user network. Please check that is using the
right cable. Use Unshielded Twisted-Pair (UTP) or Shielded Twisted-Pair (STP) cable
for RJ-45 connections:  100 Category  3,  4  or  5 cable for 10 Mbps connections or 100
Category  5  cable  for  100  Mbps  connections.  Also,  be  sure  that  the  length  of  any
twisted-pair connection does not exceed 100 meters (328 feet).

Diagnosing LED Indicators
The switch can be easily monitored through panel indicators, which describes common
problems user may encounter and where user can find possible solutions, to assist in
identifying.
If  the  power  indicator  does  not  light  up  when  the  power  cord  is  plugged  in,  user may
have  a  problem  with  power  cord.  Then  check  for  loose  power  connections,  power
losses  or  surges  at  power  outlet.  If  user  still  cannot  resolve  the  problem,  contact  the
local dealer for assistance.
If the Industrial switch LED indicators are normal and the connected cables are correct
but  the  packets  still  cannot  transmit,  please  check  your  system’s  Ethernet  devices
configuration or status.

«
...
92
93
94
95
96
...
»

Содержание EKI-7659CPI






































































































Отзывы:

Нет отзывов

Похожие инструкции для EKI-7659CPI

Бренд: Gefen Страницы: 11

xStack DES-3500 Series

Бренд: D-Link Страницы: 260

DXS-3600 Series

Бренд: D-Link Страницы: 48

DXS-3400 SERIES

Бренд: D-Link Страницы: 3

Web Smart Switch DGS-1210-16

Бренд: D-Link Страницы: 71

Бренд: D-Link Страницы: 3

Бренд: D-Link Страницы: 56

xStack DES-3800 Series

Бренд: D-Link Страницы: 326

xStack DES-3526

Бренд: D-Link Страницы: 222

Бренд: D-Link Страницы: 2

DXS-1210 Series

Бренд: D-Link Страницы: 20

SmartCell 6A000

Бренд: Cabletron Systems Страницы: 114

Бренд: Cabletron Systems Страницы: 62

CyberSWITCH CSX150

Бренд: Cabletron Systems Страницы: 49

Cabletron CyberSWITCH CSX5500

Бренд: Cabletron Systems Страницы: 729

D-PFS4226-24ET-240

Бренд: Dahua Страницы: 58

Бренд: IDEC Страницы: 5

Бренд: IDEC Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды