manualshive.com logo in svg

Advantech EBPC-5250, Руководство пользователя

Поделиться
Скачать
Advantech EBPC-5250 Скачать руководство пользователя страница 7

vii

EBPC-5250 User Manual

 

Initial Inspection

When you open the carton, please make sure that the following materials have been
shipped:

!

EBPC-5250 Chassis

!

User Manual

!

Warranty Card

!

Accessory box with a package of screws (for fastening the SBC, 3.5” disk drive, 
slim-type optical disk drive, mounting brackets, riser card), 4 pcs of rubber pads, 
a pair of mounting brackets, a label (for the pre-punched I/O ports), and a pack 
of I/O cables. 

If any of these items are missing or damaged, contact your distributor or sales repre-
sentative immediately. We have carefully inspected the product mechanically and
electrically before shipment. It should be free of marks and scratches and in perfect
working order upon receipt. As you unpack the product, check it for signs of shipping
damage. (For example, damaged box, scratches, dents, etc.) If it is damaged or it
fails to meet the specifications, notify our service department or your local sales rep-
resentative immediately. Also, please notify the carrier. Retain the shipping carton
and packing material for inspection by the carrier. After inspection, we will make
arrangements to repair or replace the unit.

Содержание EBPC-5250










































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды