Advantech ARK-1388V Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 109

Advantech ARK-1388V Скачать руководство пользователя страница 29

19

ARK-1388V User Manual

Chapter 2

H

/W installation

2.2.2.5

LED Indicators

There are six LEDs on ARK-1388V front metal face plate for indicating system status:
Normal LED detects internal temperature. When under 90° C, Normal LED flashes
blue. When the internal temperature is over 90° C, Normal LED will not flash, but
Alarm LED will flash orange; air flow should be enhanced to dissipate heat. HDD LED
is for compact flash disk status, which flashes red when active. The GPS/GPRS/DIO
LED flashes green when these functions are active. (ARK-1388VV by default has no
GPRS function, therefore the GPRS LED won't flash until user plugs in AMO-EDGE
or AMO-HSDPA; DIO function is reserved LED for user to program as its unique
application,)

2.2.2.6

GPRS Antenna

There is one SMA female connector on ARK-1388V front metal face plate for exter-
nal GPRS or HSDPA antenna. ARK-1388V by default is not equipped with GPRS/
HSDPA module; the SMA connector is reserved to connect with external antenna
which may be purchased: AMO-EDGE or AMO-HSDPA.

2.2.2.7

Power on/off bottom

ARK-1388V comes with a Power On/Off button which flashes yellow to indicate
power on.

2.2.3

ARK-1388V rear side external I/O connectors

2.2.3.1

Ethernet Connector (LAN)

ARK-1388V is equipped with an Intel 82562GZ Ethernet controller that is fully compli-
ant with IEEE 802.3u 10/100Base-T CSMA/CD standards. The Ethernet port pro-
vides a standard RJ-45 jack connector with LED indicators on the front side to show
its Active/Link status (Green LED) and Speed status (Yellow LED).

Figure 2.10 Ethernet connector

Table 2.17: RJ-45 Connector pin assignments

Pin

10/100/1000BaseT Signal Name

1

TX+

2

TX-

3

RX+

4

RJ45_CM1_R

5

RJ45_CM1_R

6

RX-

7

RJ45_CM2_R

8

RJ45_CM2_R

1

8

1

8

«
...
27
28
29
30
31
...
»

Содержание ARK-1388V














































































































Отзывы:

Нет отзывов