Advantech ARK-1388V Скачать руководство пользователя страница 15

Страница: 15 / 109

ARK-1388V User Manual

Chapter 1

eneral

Introduction

IDE Interface

SB: Intel NH82801GHM chip support

Supports PIO IDE transfers up to 16 Mbytes/sec

Supports Ultra ATA transfers to 100/66/33 Mbytes/sec.

The IDE interface integrates 16x32-bit buffers for optimal
transfers.

Supports Compact Flash Card Type II Socket

CF Socket on board: CF Type II 50P 90D(M) external con-
nector x 1

Mini PCI Interface

SB: Intel NH82801GHM chip support

Supports Mini PCI Interface 1.0

Supports Mini PCI WLAN extension card use only

Supports 802.11A/B/G when use 9680005627

Min

i PCI socket: MINI PCI 124P 180D(F) SMD x 1

Power Management

SB: Intel NH82801GHM chip support

Supports ACPI 3.0

ACPI Power Management Logic Support

Pow

er connector: Plug-In block 2P DIP x 1

USB Interface

SB: Intel NH82801GHM chip support

USB host interface with support for 4 USB 2.0 ports

All ports are High-Speed, Full-Speed, and Low-Speed capa-
ble

Supports legacy keyboard/mouse software

USB

dual connector on board: USB conn 8P 90D(M)

DIP x 2

Audio Link

SB: Intel NH82801GHM chip support

Supports Audio Codec’97, Revision 2.3 specification

Supports Link for Audio and Telephony CODECS

Supports Dual 6W Audio Amplifier Plus Stereo

RCA Jack on Board: 3P 90D(F) Red x 1 (Line-out, Right
Channel)

RCA Jack on Board: 3P 90D(F) White x 1 (Line-out, Left
Channel)

PHON

E JACK on Board: 5P 90D(F) Pink x 1 (Mic-in)

BIOS

SB: Intel NH82801GHM chip support

Low Pin Count (LPC) interface support

Firmware Hub (FWH) interface support

Phoenix 4M bit Flash BIOS, supports Plug & Play, APM 1.2/
ACPI 1.1.

Soc

ket: 32 pin PLCC socket x 1

Содержание ARK-1388V














































































































Результаты поиска

Содержание ARK-1388V

Отзывы:

Advantech ARK-1388V, Руководство пользователя, Страница: 15 / 109

Результаты поиска

Содержание ARK-1388V

Отзывы: