manualshive.com logo in svg

Advanjet HV-2100, Инструкции по ремонту

Поделиться
Скачать
Advanjet HV-2100 Скачать руководство пользователя страница 20

 

3.3 

Assemble the , continued 

 

3.3.6 

Align the Lever with the Shoulder Bolt 

 

Use an awl to line up the hole in the lever with the hole for the shoulder bolt. 

 

Insert the 2 mm driver from the opposite side and line it up with the awl.  

 

Push out the awl with the driver. 

 

3.3.7 

Install the Shoulder Bolt  

 

Apply a light coating of Loctite 242 to the threads of the shoulder bolt and wipe off any excess.  

 

Insert the shoulder bolt and push out the driver. 

 

 

Screw in the shoulder bolt with the driver until it is barely snug. Verify that the lever is not binding—
the hammer cylinder hat should move up and down freely.  

 

Note: Do not allow Loctite from the shoulder bolt tip to transfer to the lever, as this will impede jet valve 
operation. For proper operation of the shoulder bolt, do not over-tighten. 

 

HAT MOVES 

UP & DOWN 

Page 20 of 30 

Advanjet HV-2100 Jet Maintenance and Repair 

3A6326A 

Содержание HV-2100































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды