manualshive.com logo in svg

Advanced Radiant Systems COOL-SPACE CS5-16, Руководство по эксплуатации и обслуживанию, Страница: 9 / 16

Поделиться
Скачать
Advanced Radiant Systems COOL-SPACE CS5-16 Скачать руководство пользователя страница 9

7 

 

6.1 Troubleshooting (continued) 

Fan System 

 

Please use caution when troubleshooting or repairing all electrical components. Be certain that 
all power is disconnected from the

 

COOL-

SPACE

®

 

unit before the cooling pads or fan guard 

are removed to gain access to the fan.

 

 

Direct & Belt Drive Models 

 

Problem 

Check 

Solution 

Fan won't run and makes no 
sound. 

Power cord, extension cord, 
switches, circuit breaker, GFI 
ground fault. 

Reconnect power or extension 
cord. Reset breaker. 

Fan motor won

’

t run and makes 

a humming sound. 

Blade in contact with shroud. 
Motor stalled (will not turn by 
hand). 

Re-center blade hub. 
Replace motor. 

Breaker trips or fuse blows when 
fan is started. 

Motor stall. 
Check power source for min. 
220v/10 amp. Extension cord. 

Replace motor. 

Upgrade power supply. 
Replace with heavier cord. 

Motor overheating and shutting 
off. Restarting several minutes 
later. 

Extension cord gauge too small 
Inlet air obstructed or too 
close to wall 
Faulty motor 
Loose belt 

Replace with heavier cord 
Provide minimum 1 metre 
inlet clearance. 
Replace motor. 
Tighten belt 

Fan motor won

’

t run and switch 

makes soft clicking sound. 

Switch making good contact. 

Replace switch. 

Fan blade doe

sn’t turn 

and unit 

makes squealing sound. 

Motor stall (as above). Fan 
belt loose or broken. 
Fan pulley spinning on shaft. 

Replace motor. 
Tighten or replace fan belt. 
Tighten pulley set screw. 

Fan belts do not last very long. 

Motor and fan pulleys alignment. 

Realign motor and fan pulleys. 

Fan will not reach speed but 
turns and makes humming 
sound. 

Capacitor (where visible) and 
motor electrical connections. 
Extension cord to small. 

Replace capacitor or motor. 
Increase cord gauge. 

 

 

 

 

 

 

 

 

 

Содержание COOL-SPACE CS5-16

















Отзывы:

Нет отзывов