manualshive.com logo in svg

Advanced Radiant Systems COOL-SPACE CS5-16, Руководство по эксплуатации и обслуживанию, Страница: 13 / 16

Поделиться
Скачать
Advanced Radiant Systems COOL-SPACE CS5-16 Скачать руководство пользователя страница 13

11 

 

6.2 Repair procedures (continued) 

BLIZZARD (CS5-48) Belt Drive Models 

1.  Remove the motor wiring plate and disconnect motor wires. Mark each wire with a 

marker that will allow easy matching when new motor is installed. (see section 5.1 for 
pad removal instructions) 

2.  Loosen the four bolts that fasten the motor to the bracket. This will allow the removal 

of the motor. 

3.  Remove the motor pulley by loosening the set screw and slide the pulley off. 

4.  Install the pulley onto the new motor and slightly tighten the set screw. 

5.  Place new motor onto the mounting bracket and reinstall the four mounting bolts and 

tighten. 

6.  Visually align the motor pulley and fan pulley by using the belt as a reference. Adjust 

the motor pulley in or out to align. Tighten the motor pulley. 

7.  Loosen the four (4) bolts that secure the mounting bracket to the upright. 

8.  Lower the bracket slightly until the belt is tight (but not tight enough to overload the 

motor), then tighten the four bracket bolts. 

9.  Replace the motor wires as marked from step #5. Replace wire ties to prevent cord 

from getting in fan blade. 

10. Replace motor wiring cover plate and inspect to be certain that the rubber seal is 

properly seated.  

11. Replace cooling pads and guards and reconnect power and test motor. 

 

Pump Replacement (All Models) 

1.  Disconnect hose from pump. 

2.  Remove pump bracket. 

3.  Remove the 2 screws from the top of the electrical cord and unplug the cord by 

pulling straight up from the top of the pump. 

4.  Remove pump from water sump and install new pump. Reverse the above 

procedures to reconnect the wiring, pump bracket and the hose. Secure wires to fan 
frame with wire ties to clear the fan blades. 

5.  Reinstall cooling pads and guards, reconnect power and test pump. 

 

6.3 Technical support 

Technical support and service is available directly from your distributor or  
 

COOL-

SPACE

®

 Technical Support Hot Line at 001-317-577-0337 

Visit: 

www.cool-space.com

 

Email: 

[email protected]

 

 

 

 

Содержание COOL-SPACE CS5-16

















Отзывы:

Нет отзывов