Advanced Radiant Systems COOL-SPACE CS5-16 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 16

Advanced Radiant Systems COOL-SPACE CS5-16 Скачать руководство пользователя страница 6

4

4.3 Starting the pump and adjusting the water flow

DO NOT flood the pads with water, keep them moist. New pads will take a few days before they
become completely saturated. It is normal to have several dry streaks on the face of the pads
about 25 to 50 mm wide. If the streaks are larger adjust the flow control knob to allow more water
to flow onto the pads. NOTE: New pads may also emanate an odour under initial operating
conditions from the resin used to construct the media. Flush the pads by running the pump
without the fan running for approximately at least 12 hours; overnight is best. Empty the sump
and refill. Repeat if odour still exists.

NOTE:

Run fan while adjusting the water flow

Once the sump is full, the pump

switch may be turned to the ‘ON’ position.

The flow control

knob will need to be adjusted on initial start-up. It is located at the side of the unit; it
controls the volume of water that is delivered to the top of the cooling pads.

Prolonged use of hard water without proper water treatment will create mineral deposit

build up causing the pump to fail which is NOT COVERED BY WARRANTY

Pump is equipped with a

LOW WATER CUT OFF

which may take up to 5 minutes to reset each

time the power is turned on.

5.0 Maintenance and storage

ELECTRICAL SHOCK HAZARD

Disconnect the power supply before performing any service or maintenance on the unit. Failure
to do so may result in serious injury or death.

5.1 Removing the cooling media to access the inside of the unit

In order to perform any maintenance on internal components, the cooling pads must be
removed to access the inside of the unit.

1. Remove the (2) bolts connecting the pad retainer bar (pad-side) from the housing.

2.

Tilt pads from the top, starting with the center pad, out of the unit.

Note: Reinstall pads correctly according to the markings on the pads.

5.2 Daily maintenance

When shutting down the COOL-

SPACE

®

unit at the end of each workday, the pump should be

turned off approximately 15 minutes before the fan is turned off. This will allow the pads to drain
and dry out. This simple guideline will ensure long and efficient pad life as well as help to
control mildew and bacteria growth.

«
...
4
5
6
7
8
...
»

Содержание COOL-SPACE CS5-16

















Отзывы:

Нет отзывов