Advanced Measurement Technology ORTEC A-576 A-PAD Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 11

background image

7

Fig. 5. Detailed Block Diagram of the Model A-576 A-PAD.

6.7 on the 4

&

7 MeV range, or a factor of 4 on the 3

&

8

the detected input energy exceeds the selected bias

MeV range. The output of the biased amplifier is a

level. The full-scale output of 10 V can be adjusted

positive pulse with an amplitude, in the range from 0.1

down to 7.75 V, using the front-panel screwdriver

to 10 V, which is proportional to the amount by which

control (E).

«
...
9
10
11

Содержание ORTEC A-576 A-PAD












Отзывы:

Нет отзывов

Похожие инструкции для ORTEC A-576 A-PAD

Syn Power 2.050

Бренд: Macrom Страницы: 26

Бренд: icon Audio Страницы: 9

Бренд: lag Страницы: 2

Бренд: Gibson Страницы: 1

Бренд: Interface Devices Страницы: 8

Бренд: NAD Страницы: 78

Бренд: Kingray Страницы: 6

Бренд: Boss Audio Systems Страницы: 19

UP 4000 Series UP4121

Бренд: Mackie Страницы: 4

Бренд: Stagg Страницы: 2

Бренд: Crest Audio Страницы: 2

Бренд: Shure Страницы: 3

Бренд: Michigan Scientigic Страницы: 7

Digital Extender HD-D105

Бренд: RTcom Страницы: 12

Бренд: Harman Страницы: 31

Бренд: Altec Страницы: 14

Бренд: Rotel Страницы: 10

Бренд: SAL Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды