manualshive.com logo in svg

Advanced Instruments GPR-1200, Руководство пользователя

Поделиться
Скачать
Advanced Instruments GPR-1200 Скачать руководство пользователя страница 26

Advanced Instruments Inc. 

 

 

 

GAS CONCENTRATION  

 

PERCENT 

PPM 

 

 

 

 

 

    

   

 

 

 

 

 

12.

 

Select PERCENT or PPM option. After gas concentration selection, following menu appears to enter the actual span 

gas value. 

 

 

000.00 PPM 
 
PRESS UP OR DOWN 
TO CHANGE VALUE 
ENTER TO SAVE 
MENU TO RETURN  

 

 

 

>>> 

09.00  PPM 

 

SPAN 

CALIBRATION 

ENTER TO CALIBRATE 

MENU TO ABORT  

 

 

13.

 

By using the UP or DOWN arrow keys, enter the appropriate digit where the cursor is blinking 

14.

 

Press the ENTER key to advance the underline cursor right or press the MENU key to advance the underline cursor 

left to reach to the desired digit of the alarm value. 

15.

 

Repeat until the complete span value has been entered.  

16.

 

In the example above, a span value of 09.00 PPM has been entered.  

17.

 

After the span value has been entered, the analyzer will prompt to press the ENTER key to accept SPAN 

CALIBRATION. 

Caution: Allow the span gas to flow until the analyzer reading has stabilized before accepting calibration. 

The wait time will vary depending on the amount of oxygen introduced to the sensor when the sample and span gas 

lines were switched 

18.

 

After successful calibration, the analyzer will display a message “Passed Calibration” and return to the Sample 

mode.  

NOTE: The analyzer is allowed to accept calibration when O2 reading is within 50% of the span gas value. If the O2 

reading is outside of this limit, by pressing ENTER to accept calibration will result in “Failed Calibration” and return to 

the Sample mode without completing Span calibration. After pressing ENTER either of the following two messages will 

be displayed.

 

 

 

 

 

PASSED 

CALIBRATION 

 

  

 

 

  

OR 

 

 

 

FAILED 

CALIBRATION 

 

 

 

If the calibration is unsuccessful, return to the SAMPLING mode with span gas flowing through the analyzer and retry 

calibration before concluding that the analyzer is defective. 

Before disconnecting the span gas line and connecting the sample gas line (if the analyzer is not equipped with a 

SPAN/SAMPLE vale option), flow the sample gas for 1-2 minutes to purge the air inside the sample line and then 

disconnect the span gas line and replace it with the purged sample gas line. 

 

 

 

25 

 

Содержание GPR-1200






































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды