background image

61182118L1-5B

Issue 2, July 2004

    3

2. Pull the ejector latch, located on the lower left-

hand side of the 2W/4W SHDSL LTU front panel, 
from its closed position.

3. Hold the 2W/4W SHDSL LTU by the front panel 

while supporting the bottom edge of the module 
with the ejector latch opened to engage the chassis 
edge.

4. Align the module edges to fit in the lower and 

upper guide grooves for the access module slot.

5. Slide the module into the access module slot. 

Simultaneous thumb pressure at the top (above the 
PWR LED) and at the bottom (below the 
electrostatic caution symbol) of the module will 
ensure that the module is firmly seated against the 
backplane of the chassis. 

6. Secure the 2W/4W SHDSL LTU in place by 

pushing in on the ejector latch.

When the 2W/4W SHDSL LTU first powers up it runs 
the power up self-tests. Once the power up self-test is 
complete, the status LEDs will reflect the true state of 
the hardware.

Front Panel LEDs

The 2W/4W SHDSL LTU Access Module provides 
front panel LEDs to display status information. See 

Table 2

 for a listing of the front panel LEDs and their 

indications.

4. PROVISIONING

All SHDSL LTU menus are accessed via the SCU. The 
Total Access 3000 SCU provides a front panel DB-9 
connector that supplies an RS-232 interface for 
connection to a controlling terminal. The pinout of the 
DB-9 is illustrated in 

Figure 2

.

Figure 2.  RS-232 (DB-9) Pin Assignments

The terminal interface can operate at data rates of 9.6, 
19.2, 38.4, 57.6, and 115.2 kbps. The asynchronous data 
format is fixed at 8 data bits, no parity, and 1 stop bit. 
The supported terminal type is VT100 or compatible.

6

7

8

9

1

2

3

4

5

TXD (Transmit Data)

RXD (Receive Data)

SGN (Signal Ground)

Table 2.  Front Panel LEDs

Front Panel

LED

Indication

Description

PWR

Off

Green

Yellow

Flashing (any color)

No power, or fuse failure
Self-test passed and the module is In-Service
Self-test passed and the module is Out-of-Service
VT100 menu session in progress

SHDSL

Off

Green

Red

Module is Out-of-Service, Unassigned
Module has achieved synchronization with the NTU
Module has not achieved synchronization with NTU

G.703

Off

Green

G.703 port not configured (Out-of-Service, Unassigned), 
or an alarm condition exists
G.703 port configured and no alarms exist

TST

Off

Green

Blinking Green

Red

Module is not in loopback or BERT
Local loopback is active, or BERT running with no errors
Module is running a BERT with bit errors
Module is running a BERT with no pattern sync

ALM

Off

Yellow

Red

No alarm condition detected
Remote alarm condition detected
Alarm condition detected locally

PWR

TEST

SHDSL

ALM

SHDSL

1182118L1

G.703

Содержание Total Access SHDSL LTU















Отзывы: