Adtec RD-60 Скачать руководство пользователя страница 20

Страница: 20 / 61

will be used.

Downscaling
SDI

The Downscaling SDI setting
determines whether the SDI

bank ( SDI Output 1 and 2 ) will
be output natively or downscaled

to SD.

OFF
SD

Downscaling

SDIALT

The Downscaling SDI setting

determines whether the SDI
bank ( SDI Output 3 and 4 ) will

be output natively or downscaled
to SD.

OFF

Genlock Menu

Genlock Mode

Configures the genlock operation
of the decoder. SLAVE is
primarily used for 3D applications
and REMOTE is used in standard
genlock operation.

OFF - Disables genlock
SLAVE - Enable Genlock, Decode
source is synchronous to SYNC IN
signal
REMOTE - Enable genlock, Decode
source is NOT synchronous to SYNC
IN signal

Horizontal

Adjust

Horizontal adjustment defines

the difference in the SYNC IN
HSYNC and output HSYNC.

Typically, this should be in the
range of 0 to +1 line in clocks.

For example, a 1080I output
could be adjusted from 0 to

2200.

0 - 2200

Vertical Adjust

Vertical adjustment defines the

difference in the SYNC IN VSYNC
and output VSYNC. Typically, this

should be in the range of 0 to +1
frame in lines. For example, a

1080I output could be adjusted
from 0 to 1125.

0 - 1125

Pixel Phase

Pixel Phase adjustment is a very
fine grain adjustment that can

adjust within a single clock. The
increments are 1/64th of a clock.

The valid range is 0 to 63.

0 - 63

Genlock Status

Shows if GENLOCK input is

currently being used for the
decoder or in FREE RUN mode

Genlock CVBS

This configuration is used

VIDEO - CVBS output is video

Содержание RD-60






























































Результаты поиска

Содержание RD-60

Отзывы:

Похожие инструкции для RD-60

Бренды по названию

Популярные бренды

Adtec RD-60, Руководство пользователя

Результаты поиска

Содержание RD-60

Отзывы:

Похожие инструкции для RD-60

Бренды по названию

Популярные бренды