manualshive.com logo in svg

ADLINK Technology aTCA-3710, Руководство пользователя

Поделиться
Скачать
ADLINK Technology aTCA-3710 Скачать руководство пользователя страница 65

                                                 aTCA-3710 User's Guide

 

 
 

 65 

 

„

 

-H <IP address >   

The parameter specifies the IP address of the IPMC. 

Perform the following steps to update firmware: 

Step1:

 Prepare an external host PC with Linux OS and connect it to the target aTCA-3710 via Base 

Interface. Put the IPMItool utility and the new firmware image on the host PC. Enter the following 
command: 

[root@localhost 3710]# ./ipmitool –I lan –H 172.17.172.134 hpm upgrade hpm1fw.img 
activate 

 

Step2: 

Select “y” when prompted and wait until the string “firmware update procedure successful” is 

displayed. 

 

To update other images (IPMC BOOT LOADR, FPGA, etc), just replace the target image and the file 
name while typing command. 

 

Item 

File name 

IPMC firmware 

hpm1fw.img 

IPMC Boot Loader 

hpm1boot.img 

FPGA hpm1iap.img 

 

Note:  

1.  Make sure the payload power is off (M1 state) before updating the FPGA firmware. 
 

Содержание aTCA-3710






































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды