ADLINK Technology aTCA-3710 Скачать руководство пользователя страница 28

Страница: 28 / 69

aTCA-3710 User's Guide

Byte

Data Field

Event Status” command for the sensor before the update has completed. This is most likely to be the

case for sensors, such as

fan RPM sensors, that may require seconds to accumulate the first reading after a re-arm.

[4:0] – Reserved. Ignore on read.

[7:4] – Reserved. Write as 0h, ignore on read

[3] 1b = IPMB A enabled, IPMB-B enabled

[2] 1b = IPMB A disabled, IPMB-B enabled

[1] 1b = IPMB-A enabled, IPMB-B disabled

[0] 1b = IPMB A disabled, IPMB-B disabled

(5)

[7:0] – Optional/Reserved. If provided, write as 80h (IPMI restriction). Ignore on read.

5.3.3 Watchdog Timer Sensor

Sensor Type

Sensor

Type Code

Sensor

Specific Offset

Event

Watchdog 2

23h

00h

01h

02h

03h

04h-07h

08h

This sensor is recommended for new IPMI v1.0 and later implementations.

Timer expired, status only (no action, no interrupt)

Hard Reset

Power Down

Power Cycle

reserved

Timer interrupt

The Event Data 2 field for this command can be used to provide an

event extension code, with the following definition:

7:4 interrupt type

0h = none

1h = SMI

2h = NMI

3h = Messaging Interrupt

Fh = unspecified

all other = reserved

3:0 timer use at expiration:

0h = reserved

1h = BIOS FRB2

2h = BIOS/POST

3h = OS Load

4h = SMS/OS

5h = OEM

Fh = unspecified

all other = reserved

Содержание aTCA-3710






































































Результаты поиска

Содержание aTCA-3710

Отзывы:

Бренды по названию

Популярные бренды

ADLINK Technology aTCA-3710, Руководство пользователя

Результаты поиска

Содержание aTCA-3710

Отзывы:

Бренды по названию

Популярные бренды