manualshive.com logo in svg

ADLINK Technology aTCA-3710, Руководство пользователя

Поделиться
Скачать
ADLINK Technology aTCA-3710 Скачать руководство пользователя страница 46

                                                 aTCA-3710 User's Guide

 

 
 

 46 

8 Getting Started 

The aTCA-3710 has been designed for easy installation. However, the following standard precautions, 
installation procedures, and general information must be observed to ensure proper installation and to 
preclude damage to the board, other system components, or injury to personnel.   

8.1 Safety 

Requirements 

The following safety precautions must be observed when installing or operating the aTCA-3710. ADLINK 
assumes no responsibility for any damage resulting from failure to comply with these requirements.     

Do not touch the heatsink when installing or removing the board. The board should not be placed on any 
surface or in any form of storage container until the board and heat sink have cooled down to room 
temperature.   

This ATCA blade contains electrostatic sensitive devices. Please observe the necessary precautions to 
avoid damage to your board:   

„

 

Discharge your clothing before touching the assembly. Tools must be discharged before use.   

„

 

Do not touch components, connector-pins or traces.   

„

 

If working at an anti-static workbench with professional discharging equipment, please do not omit 
to use it. 

8.2 Quick 

Start 

8.2.1 Hardware Configuration Settings 

For normal operation, it is not recommended to change any onboard hardware configuration settings, but 
there are some options on the board for those want to investigate more flexibility for testing. Figure 14 below 
shows the locations of the hardware configuration switches and jumpers. 

Содержание aTCA-3710






































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды