background image

16

Special Note: Line Termination. When longer runs of cable are used, you may need to use a terminator 

on the last unit to avoid erratic behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is 

connected between pins 2 and 3 of a male XLR connector (DATA + and DATA -). This unit is inserted 

in the female XLR connector of the last unit in your daisy chain to terminate the line. Using a cable 

terminator (ADJ part number Z-DMX/T) will decrease the possibilities of erratic behavior.

D M X   S E T U P

DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used as a form of communication 

between intelligent fixtures and controllers. A DMX controller sends DMX data instructions from the 

controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture via the DATA 

“IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only have a DATA 

“OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models of different manufactures to be 

linked together and operate from a single controller, as long as all fixtures and the controller are DMX 

compliant. To ensure proper DMX data transmission, when using several DMX fixtures try to use the 

shortest cable path possible. The order in which fixtures are connected in a DMX line does not influence 

the DMX addressing. For example; a fixture assigned a DMX address of 1 may be placed anywhere in 

a DMX line, at the beginning, at the end, or anywhere in the middle. When a fixture is assigned a DMX 

address of 1, the DMX controller knows to send DATA assigned to address 1 to that unit, no matter 

where it is located in the DMX chain.

Data Cable (DMX Cable) Requirements (For DMX and Master/Slave Operation):

The Vizi BSW 300 can be controlled via DMX-512 protocol. The Vizi BSW 300 

has 2 DMX channel modes; 17 channel mode, and 20 channel mode. The DMX 

address is set electronically using the controls on the front panel of the unit. 

Your unit and your DMX controller require a approved DMX-512 110 Ohm Data 

cable for data input and data output. We recommend Accu-Cable DMX cables. 

If you are making your own cables, be sure to use standard 110-120 Ohm 

shielded cable (This cable may be purchased at almost all professional sound 

and lighting stores). Your cables should be made with a male and female XLR 

connector on either end of the cable. Also remember that DMX cable must be 

daisy chained and cannot be split.
Notice: Be sure to follow figures two and three when making your own cables. 

Do not use the ground lug on the XLR connector. Do not connect the cable’s shield conductor to the 

ground lug or allow the shield conductor to come in contact with the XLR’s outer casing. Grounding the 

shield could cause a short circuit and erratic behavior.

Содержание Vizi BSW 300





































Отзывы: