background image

 

 

 

 

BEFORE USE 

 

HANDLING OF THE PACKED MACHINE 

The machine is supplied with suitable packing foreseen for fork lift 

truck handling.   

For the package dimensions please look at the “TECHNICAL 

DESCRIPTION” table. 

 

 

Do not place any packings on top. 

 

UNPACKING THE MACHINE 

1.

 

Remove the external packing. 

2.

 

Move the machine backwards, as indicated in the figure, avoiding 

heavy contacts to mechanical parts. 

 

 

 

3.

 

Keep the pallet for eventual transport. 

 

 

The portable slope is not included in the packaging. 

 

ACCESS TO THE BATTERY COMPARTMENT 

1.

 

Bring the machine on a levelled surface. 

2.

 

Rotate the seat platform forward up to the blocking of the 

support.  

3.

 

Having finished any intervention, to close the battery 

compartment, after having released the support, reposition the 

seat platform. 

 

 

 

BATTERY INSTALLATION AND SETTING OF THE BATTERY TYPE 

The machine is equipped either with batteries in serial connection or 

elements of DIN-type assembled together and connected in series for a 

total of 36 Volt, placed in its appropriate compartment under the seat 

platform and must be handled using suitable lifting equipment (due to 

weight, considering the type of batteries chosen, and coupling system). 

The batteries must be in accordance with CEI 21-5 Norms. 

 

 

 

 

The machine and its battery check card foresee the use of traditional 

lead batteries. 

CHECK THE SETTING OF THE CHECK CARD (see under paragraph 

"BATTERIES CHARGE LEVEL INDICATOR"). 

In case of GEL batteries installation, it is necessary to set the check card. 

Please contact the authorized technical assistance. 

 

Strictly follow manufacturer/distributor indications for the 

maintenance and recharge of the batteries. All installation and 

maintenance operations must be executed by specialized staff, using 

suitable protection accessories. 

 

For batteries installation it is necessary to reach the battery 

compartment as indicated under paragraph “ACCESS TO THE BATTERY 

COMPARTMENT”. 

1.

 

Place the batteries in its compartment. 

2.

 

Connect the terminals, respecting the polarities, avoiding 

contact with other parts that could create short circuit. 

 

ASSEMBLING OF THE ROLLBAR 

For packing reasons,  the support of the blinking light is supplied 

disassembled. 

Proceed as follows: 

Take off the four fixing screws (1) from the rollbar. 

Place the rollbar into their seats (2) on the tank. 

Fasten the screws passing them in the same order in their holes 

foreseen on the support. 

Complete the assembly connecting the connectors (3) to supply the 

blinking light. 

 

 

 

BATTERY CHARGER 

 

 

Make sure that the battery recharger is suitable for the installed 

batteries both for their capacities and type (lead/acid or GEL and 

equivalent). 

In the plastic bag containing the use and maintenance you will find the 

coupling connector for the recharger. It must be assembled onto the 

cables of your recharger, following the instructions given by the 

manufacturer. 

 

CHARGING THE BATTERIES 

1.

 

Plug the connector (3) of the battery recharger into the battery 

connector. 

2.

 

Proceed for the recharging. 

 

Содержание diamond 100 AC




















Отзывы: