background image

- 24 -

- 25 -

10  TECHNICAL SPECIFICATION

ADEY reserve the right to amend the specification without notice .

10 .11 

Noise:  The equivalent continuous A-weighted sound pressure level at a  

 

 

distance of 1 metre from the pump does not exceed 70 dB(A) .

11  TROUBLE SHOOTING GUIDE

Symptoms

Error Code

Probable Cause

Recommended Action

Pump(s) not 

starting

No power to APU

Ensure the green light is on the front of the APU, check fuse .

Low water

Low water in tank

Depress float valve to varify water is filling tank, check water level and 

supply .

System pressure = 

set pressure

APU functioning correctly . Check the set system pressure .

Sensor error

Pressure sensor fault

Remove pressure from the APU outlet and verify the displayed pressure 

is 0 bar . Er will be displayed if the sensor signal is outside parameters . 

(Replace sensor – call ADEY) .

Pump(s) will not 

stop

System pressure set 

too high

System set pressure is set higher than the pump performance capability, 

reduce set pressure . Ensure you have purchased the correct APU for the 

system pressure required .

Sensor error

Pressure sensor fault

Remove pressure from the APU outlet and verify the displayed pressure 

is 0 bar . Er will be displayed if the sensor signal is outside parameters . 

(Replace sensor – call ADEY) .

Low pressure alarm 

triggered

Low pressure

Leak in system .

Check system for leaks . Check for leaking pressure relief valve .

Low pressure alarm 

set too high .

Reduce Low press alarm pressure . Check system pressure range during 

normal operation .

Sensor error

Pressure sensor fault

Remove pressure from the APU outlet and verify the displayed pressure 

is 0 bar . Er will be displayed if the sensor signal is outside parameters . 

(Replace sensor – call ADEY) .

High pressure 

alarm triggered

High pressure

System pressure 

too high

Check system operation . Increase High presure alarm set pressure .

Sensor error

Pressure sensor fault

Remove pressure from the APU outlet and verify the displayed pressure 

is 0 bar . Error will be displayed if the sensor signal is outside parameters . 

(Replace sensor – call ADEY) .

Sensor failure error Sensor error

Pressure sensor 

outside specifcation

Remove pressure from the APU outlet and varify the displayed pressure 

is 0 bar . Er will be displayed if the sensor signal is outside parameters . 

(Replace sensor – call ADEY) .

Water overflowing 

warning pipe or 

weir

Water level too high

Check function of the fill valve, replace or adjust if needed .

Manifold NRV leaking

Isolate APU from system and mains water and replace non-return valve 

and manifold .

Mini 130

CP1-03-04911

Mini 230

CP1-03-04912

General

Guarantee

2 year

Approvals

CE

Features

System capacity

Up to 6,000 litres

Mounting

Wall mount

Pump control system

Intelligent control interface

System fill mode

-

-

Dry run protection

Noise

60 dB(A)

60 dB(A)

Materials

Break tank

Polyethylene

Front cover

Acrylic capped ABS

Performance

Maximum Fill Pressure

3 .0 bar (300 kPa)

Maximum flow

1 l/min

Maximum inlet pressure (tank fill valve)

7 bar (700 kPa)

Maximum working pressure

6 bar

Ambient air temperature

Min 4 

o

C / Max 40 

o

C

Relative humidity

95 % non-condensing

Min ./Max . water temperature

Min 4 

o

C / Max 23 

o

C

Water tank

Usable capacity

2 litres

Inlet valve and fill rate

Torbeck (side entry)  12 l/min

Fluid category

CAT 5 (type AB air gap with weir)

Connections

Cold water inlet (flexible hose)

G ½ male

Cold water outlet (flexible hose)

15 mm compression x 600 flexible hose

Overflow (compression fitting)

G ¾ (19 - 23 mm diameter pipe)

Pump

Number of pumps / pump mode

1 / Duty

2 / Duty-standby

Pump type / motor type

Solenoid / piston

Duty rating (unit)

Int 30 mins on/30 mins off (S3)

Continuous (S1)

Pump head and seal

PA66/POM  NBR

Electrical

Power supply / phase / frequency

230/1/50

Power consumption

100 Watts

Current (full load)

0 .5 Amps

Fuse rating

5 Amps

Power cable (pre-wired)

1 .5 metres

Alarm output

Single

Physical

IP rating

IPX4

Width

293 mm

Depth

145 mm

Height

403 mm

Weight (including fittings)

3 .6 Kg

4 .2 Kg

Weight (filled)

6 .6 Kg

7 .2 Kg

Содержание Mini 130


















Отзывы: