Adeunis RF ARF54 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 25

background image

Ref. 08-07-V6-lmn

p. 13

A

RF54

User Guide

Command mode

The command mode is used to read and update the modem configuration
registers using AT command.

N

OTE

The AT command can be locked using ATPWD command.

In command mode, the radio is inhibited (reception and transmission),
excepted when using test command.

Entering command mode :

issues on the serial link a +++ sequence. The

sequence of 3 conse characters is accepted only if no character have

been seen before and after the +++ sequence. Register (S214) defines the
silence duration.

Tips 1:

if you are using a terminal (such as Hyperterm), you have to send

the +++ sequence using a text file (first create a text file containing only the
+++ characters, and then use in Hyperterm the command “Send text file” in
the “Transfer menu”)

Tips 2:

Idle line for S214

duration

+++ (consecutive)

Idle line for S214
duration

+

+

+

TRANSCEIVER MODE

COMMAND
MODE

RXD

line

Exiting command mode

(return back in transceiver mode): send the serial

command

ATO <cr>

Downloaded from

electronic components distributor

«
...
13
14
15
16
17
...
»

Содержание ARF54


























Отзывы:

Нет отзывов

Похожие инструкции для ARF54

Бренд: Barco Страницы: 6

Бренд: Nabco Страницы: 35

Бренд: Omnex Страницы: 9

Бренд: Omegon Страницы: 6

Бренд: WATERLOO Страницы: 8

Бренд: Xantrex Страницы: 56

Бренд: Xantrex Страницы: 2

Freedom Sequence

Бренд: Xantrex Страницы: 58

Бренд: Xantrex Страницы: 4

Бренд: Xantrex Страницы: 20

Бренд: Vertiv Страницы: 2

Бренд: Quantum Страницы: 20

Бренд: Gemini Страницы: 9

Бренд: M-system Страницы: 18

Бренд: YASKAWA Страницы: 12

Бренд: phytron Страницы: 55

Бренд: Mosa Страницы: 28

Бренд: Broadcast Tools Страницы: 39

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды