ADB M 5083 Скачать руководство пользователя страница 43

Страница: 43 / 70

Web page

www.adblighting.com

User Manual - page 41
Issue 1.1

6.5 ArtNet configuration

Click ArtNet and then click the browser’s refresh icon to view the

WARP’s

current setting:

Function Description

ArtNet Enable

Enables or disables the Network

ArtNet SubNet

ArtNet SubNet (Value between 0 – 15)

ArtNet universe

ArtNet Universe (Value between 0 – 15)

Enable transmission of
ArtDMX on XLR5

WARP

includes a ArtDMX (Ethernet) to DMX converter, allowing daisy-

chaining of

WARPs

by means of DMX cables

Unit Name

User-defined name for the unit; default name = ADB-

WARP

ArtNet IP address

The fixed IP address is an ArtNet IP address, i.e. starting with 2 or 10.
Each

Motorised WARP

has a unique factory-set fixed IP address that is

created on the basis of its serial number. It is also possible to work with
DHCP-assigned IP addresses.
Note: Fixed IP address will disable the DHCP functionality.

ArtDMX has priority
over incoming XLR5
DMX

The default priority is ‘DMX has priority over ArtDMX’. Ticking this box will
invert this priority.

You can edit the parameters on the browser; Set or Save will send these parameters to the

WARP

Содержание M 5083







































































Результаты поиска

Содержание M 5083

Отзывы:

Бренды по названию

Популярные бренды

ADB M 5083, Руководство пользователя

Результаты поиска

Содержание M 5083

Отзывы:

Бренды по названию

Популярные бренды