ADB M 5083 Скачать руководство пользователя страница 38

Страница: 38 / 70

Operation

User Manual - page 36

www.adblighting.com

Issue 1.1

171 to 175

User setting 2

For future releases

176 to 180

User setting 3

For future releases

181 to 185

Not used

186 to 190

DMX address setting

For future releases

191 to 195

Accessory change

Going to initial position and freeze wheels
Needs Online function to restart

196 to 200

Gobo Mode indexed

201 to 205

Gobo Mode indexed
and Endless rotation

00000 to 39167: Index 0 to 430 degree
39168 to 51455: Clockwise fast to slow rotation
51456 to 53247: Stopped
53248 to 65535: Counter Clockwise slow to fast
rotation

206 to 210

Not Used

211 to 215

Not Used

216 to 220

Not Used

221 to 225

Not Used

226 to 230

Not Used

231 to 235

Not Used

236 to 240

Not Used

241

255

Arm

“Arms" Standby for fire, the command previous
selected

Note: Difference between Reset and Calibration

Calibration

Pan & Tilt

WARP

is using absolute positioning technology;

a calibration will measure all possible positions Pan and Tilt
can have. The Calibration takes up to 20 minutes.

Rings

A calibration will detect the physical limits of the wheel.(Only for
lenses)

Only necessary for maintenance purposes.

IRIS/GOBO

Calibration is forbidden if the accessory is inserted

Reset

Reset will verify the optical sensors for the rings. A reset of the

wheels is included in each start up.

Содержание M 5083







































































Результаты поиска

Содержание M 5083

Отзывы:

Бренды по названию

Популярные бренды

ADB M 5083, Руководство пользователя

Результаты поиска

Содержание M 5083

Отзывы:

Бренды по названию

Популярные бренды