manualshive.com logo in svg

ADB M 5083, Руководство пользователя

Поделиться
Скачать
ADB M 5083 Скачать руководство пользователя страница 27

Installation 

 

 

 

 

 

www.adblighting.com

 

User Manual - page 25 
Issue 1.1 

3.6  Learn Boundaries for Pan & Tilt

8

 

When 

WARP

 is positioned in a niche, or between pieces of scenery, you may wish to restrict 

its range of pan & tilt movements.  
Learn Boundaries is an automatic tool for detection of the physical boundaries.  

 

WARP

 will remember the ‘allowed window of movement’ and will then shift (offset) the DMX 

values so that  
‘Pan DMX value = zero’ matches one of the two Pan boundaries. 
‘Tilt DMX value = zero’ matches one of the two Tilt boundaries. 
 
DMX value 0 (zero) for Pan equals the Pan position of “first obstacle encountered during 
Learn Boundaries”.  
DMX value 0 (zero) for Tilt equals the Tilt position of “first obstacle encountered during Learn 
Boundaries”.  
 
If you increase a DMX value then the luminaire will move exactly as when no boundaries are 
set. 
 
Increasing the DMX values will move 

WARP

 towards the other boundary, which will be 

reached for some unknown DMX value. Any DMX value above this upper limit will be limited, 
so that 

WARP

 will not touch the obstacle.  

 
 

Note:  The limits detected during Learn Boundaries are applied until you 
perform a new Learn Boundaries. 

 
 

3.7  Configuration – presence of iris/gobo holder 

Configuration covers the presence (or not) of an iris+gobo or gobo+gobo accessory.  
The configuration settings MUST be correct or the 

Motorised WARP

 will not operate properly. 

(Menu structure) The configuration is saved in the 

Motorised WARP

.  

 
Inserting a gobo or an Iris is done by configuring the slot. The slot can be configured by using 
the ‘menu functions’ (see chapter Menu structure) or by using the ‘webpage’ (see chapter 
webpage). It is important to configure the slot before inserting the accessory into the 

WARP

. 

 

                                                 

8

 Under Development. 

 

Содержание M 5083







































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды