ADB L-854 Скачать руководство пользователя страница 28

Страница: 28 / 40

L-854 Radio Control Equipment
96A0390 Rev.J

DISCLAIMER / WARRANTY

2.6 Troubleshooting

Refer to Table 11, Table 12 and Table 13. This section provides troubleshooting information
for the L-854 Radio Control Equipment.

Table 11:

L-854 Radio Control Equipment Error Codes

Table 12:

L-854 Radio Control Equipment Warning Codes

Table 13:

L-854 Radio Control Equipment Troubleshooting

WARNING

• Allow only qualified personnel to perform the following tasks. Observe

and follow the safety instructions in this document and all other related
documentation.

• Make sure power to the L-854 has been disconnected before attempting

to service the Radio Control Equipment.

Failure to follow these warnings may result in serious injury or
equipment damage.

Code

Description

Solutions

REQ SET

Unable to set tuner frequency

Replace Radio Control Board

FRQ LOAD

Unable to load the frequency assignment
from Non-Volatile Memory (Record can
not be found)

Replace Radio Control Board

TNR INIT

Unable to initialize the tuner (typically an
internal processor error)

Replace Radio Control Board

DSP INIT

Unable to initialize the display board

Replace Radio Display Board

RTC INIT

Unable to initialize the RTC chip

Replace Radio Control Board

ROM INIT

Unable to initialize the Nonvolatile
memory

Replace Radio Control Board

A/D FAIL

The A/D Converter has failed

Replace Radio Control Board

ROM CKSM

ROM Checksum failure

Replace Radio Control Board

Code

Description

Solutions

FRQ LOCK

The synthesizer is not indicating that it is
locked to it’s assigned frequency

Replace Radio Control Board

FRQ SAVE

Unable to save the assigned frequency to
non-volatile memory

Replace Radio Control Board

RTC SAVE

Unable to save to the RTC chip. The
power outage logic won’t restore the
commanded lighting state

Replace Radio Control Board

RTC LOAD

Unable to load data from the RTC chip

Replace Radio Control Board

LOW 5V

5 volt power is below 4.7V DC

Replace Power Supply Board

HIGH 5V

5 volt power is above 5.3V DC

Replace Power Supply Board

LOW 3.3V

3.3 volt power is below 3.0V DC

Replace Power Supply Board

HIGH 3.3V

3.3 volt power is above 3.6V DC

Replace Power Supply Board

Problems and Possible Causes

Solutions

Problem:

No STATUS light

• DECODER switch set to Disable

Place DECODER switch to Enable

Содержание L-854









































Результаты поиска

Содержание L-854

Отзывы:

Похожие инструкции для L-854

Бренды по названию

Популярные бренды

ADB L-854, Руководство по эксплуатации

Результаты поиска

Содержание L-854

Отзывы:

Похожие инструкции для L-854

Бренды по названию

Популярные бренды