Step 4:
Install the M10 x 35mm long eyebolts with flat
washers on the outer front holes of the side speaker
(Figure 3).
Step 5:
Install the M10 x 35mm long eyebolt on the
top rear of the speaker then bridle to a single pull
back cable (Figure 3). For dual pullback point attach
a pullback cable on each rear eyebolts.
Step 6:
When all joiner plates are installed, tighten
screws permanently.
Step 7:
Attach a load rated suspension cables
or chains on the top front eyebolts. Use the rear
eyebolts for pull back points and to adjust the tilt
angle of the loudspeaker cluster assembly as shown
in the main illustration (Figure 4).
Step 8:
Check all hardware connections before
hoisting cluster.
Installation Guide
2010 ATM Fly-Ware, Signal Hill, CA 90755 (562) 424-1100
Rev. 00 -050510
Figure 2
Figure 3
Step 3:
Carefully flip the two speakers together so that the top is facing up.
Removed the screws in the holes where the joiner plates are installed.
Install the joiner plates using the same holes as the bottom joiner plates
using the provided screw, split washer and flat washer (Figure 3).
Step 4:
Install the M10 x 35mm long eyebolts with flat washers on the outer front
holes of the side speaker (Figure 3).
Step 5:
Install the M10 x 35mm long eyebolt on the top rear of the speaker then
bridle to a single pull back cable (Figure 3). For dual pullback point
attach a pullback cable on each rear eyebolts.
Step 6:
When all joiner plates are installed, tighten screws permanently.
Step 7:
Attach a load rated suspension cables or chains on the top front
eyebolts. Use the rear eyebolts for pull back points and to adjust the tilt
angle of the loudspeaker cluster assembly as shown in the main
illustration (Figure 4).
Step 8:
Check all hardware connections before hoisting cluster.
Figure 4
2010 ATM Fly-Ware, Signal Hill, CA 90755 (562) 424-1100
Rev. 00 -050510
Figure 2
Figure 3
Step 3:
Carefully flip the two speakers together so that the top is facing up.
Removed the screws in the holes where the joiner plates are installed.
Install the joiner plates using the same holes as the bottom joiner plates
using the provided screw, split washer and flat washer (Figure 3).
Step 4:
Install the M10 x 35mm long eyebolts with flat washers on the outer front
holes of the side speaker (Figure 3).
Step 5:
Install the M10 x 35mm long eyebolt on the top rear of the speaker then
bridle to a single pull back cable (Figure 3). For dual pullback point
attach a pullback cable on each rear eyebolts.
Step 6:
When all joiner plates are installed, tighten screws permanently.
Step 7:
Attach a load rated suspension cables or chains on the top front
eyebolts. Use the rear eyebolts for pull back points and to adjust the tilt
angle of the loudspeaker cluster assembly as shown in the main
illustration (Figure 4).
Step 8:
Check all hardware connections before hoisting cluster.
Figure 4
Figure 3
Figure 4
Adaptive Technologies Group
1635 E. Burnett Street | Signal Hill, CA 90755 USA
Ph: 562.424.1100 | Fax: 562.424.3520
www.adapttechgroup.com
ALWAYS INSTALL SAFETY CABLES
WARNING:
Mounting and/or suspension of audio and video equipment requires
experienced professionals. Improperly installed loudspeakers can result in property
damage, personal injury and/or liability to the installing contractor.
FP-EVH1152-2X1
ELECTRO-VOICE CLUSTER PACK PLANAR ARRAY KIT
