Adam Eco4 Скачать руководство пользователя страница 12

Страница: 12 / 52

Manual

Remote

Slide

Manual

Remote

Pilot Assembly &

Thermocouple Oxy pilot NG

Oxy pilot NG

Thermocouple Oxy pilot LPG

Thermocouple

T100/1332 250

84009079000

T100/1332 250

18700/376

Valve

CPMM

ACS2 LP valve Peerless

CPMM

ACS2 LP valve

18700/357 81104711000

VCV-89

18700/357 81104711000

Linier

Valve

Injector

MULAK-B MULAK-B MULAK-A BREAY-180

BREAY-180

1 2

SECTION 5.1

PREFABRICATED FLUE BOXES

This appliance can be fitted into a number of flue boxes provided that the minimum

dimensions required for the appliance are complied with.

The frame of the fire, any back panel or other infill panels, and the flue box must be

sealed together so that there is no possibility of leakage between them.

The correct clearances to combustible materials (i.e. false chimney breast etc) must be

adhered to.

The manufacturers’ instructions for fitting the prefabricated box must be complied with

at all times.

To fit the fire using the cable fixing kit supplied, some minor adaption may be necessary

for certain flue boxes.

Please ensure the firebox does not obscure the flue box outlet.

The firebox, base of the flue box, and hearth below may be drilled to allow plugs and

screws to secure installation.

It is important that the sealing requirements of the appliance are met at all times and

that the flue box is sealed to any back or infill panel.

Note: The DEPTH dimension is inclusive of any back or infill panel.

DEBRIS SPACE

In accordance with BS 5871 part 2, minimum debris collection volumes are required

behind the installed appliance.

CLAY/CEMENT LINES OR BLOCK FLUE WHICH IS NEW, UNUSED, OR PREVIOUSLY ONLY

USED WITH A GAS FIRE.

Appliance recessed depth + 20mm

UNLINED FLUE OR CHIMNEY WHICH HAS BEEN PREVIOUSLY USED FOR A SOLID FUEL OR

OIL BURNING APPLIANCE

Appliance recessed depth + 60mm

SECTION 06

Содержание Eco4





















































Результаты поиска

Содержание Eco4

Отзывы:

Похожие инструкции для Eco4

Бренды по названию

Популярные бренды

Adam Eco4, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Eco4

Отзывы:

Похожие инструкции для Eco4

Бренды по названию

Популярные бренды