Adam Eco4 Скачать руководство пользователя страница 40

Страница: 40 / 52

4 0

SECTION 18

OPERATING THE APPLIANCE (Remote control)

For your safety, the fire is fitted with a Flame Supervision Device (FSD), which will shut off

the gas supply if for any reason the pilot is extinguished.

This device incorporates a fixed probe, which senses heat from the pilot burner flame, if

the probe is cooled, the device will prevent any gas flow.

If for any reason the flames go out or if the fire has been turned off for any reason,

always

WAIT FOR 3 MINUTES

before attempting to re-light.

The pilot is visible through the Fuel bed at the front of the fire; rotate the coals for good

viewing

Fit the 9V battery in the hand set by pushing in the tab on the back of the hand set

and pulling up, locate the battery,Then fit the 6 AA batteries in the holder following the

sequence as shown on the holder and attach to the cable on the fire using the press

connection. Cover with the heat shield as described on page 21.

To light the fire, point the handset to the sensor on the front your fire.

Press and hold the two buttons together, on the left hand side of the handset.

The fire will give out a beep sound and you can

release the buttons.

After a few seconds you will hear the spark

clicking spark to the pilot light.

Once the pilot is lit the fires main burner will

come on to the high position (this whole

process will take no more than 20 seconds).

To turn down the fire, point the handset to the

sensor on your fire then push and hold the

minus button (small flame), if you release

immediately the flame will go to low if you

keep holding the flame will lower slowly and

you can release the button to your desired

position.

The fire may be left in the standby mode (pilot

only) by pressing the small round button on the

handset.

To turn your fire off, point the handset at the

sensor and push the top left button and hold.

The fire will go out.

Содержание Eco4





















































Результаты поиска

Содержание Eco4

Отзывы:

Похожие инструкции для Eco4

Бренды по названию

Популярные бренды

Adam Eco4, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Eco4

Отзывы:

Похожие инструкции для Eco4

Бренды по названию

Популярные бренды