Adam Equipment pgw 1502e Скачать руководство пользователя страница 35

Страница: 35 / 48

Page 35 of 48

13.5 CALIBRATION SETUP

This menu allows the user to set the calibration parameters.

•

Press

[Enter]

when “CAL SETUP” is displayed to select the calibration

parameters

•

The options for each parameter can be scrolled through by using the

[Up]

[Down]

key

ENABLE

NO =operator calibration is disabled
YES=operator calibration is enabled

CAL

REPORT

On = Enabled. Prints out Calibration
report after successful calibration
OFF = Disabled

TIME CAL

On = Enabled. Select time from 1 to 24
hours. Default setting is 4 hours
OFF = Disabled

TEMP CAL

On = Enabled. If set to On, set the
temperature variation from 0.2 to 4°C
OFF = Disabled

INT CAL
(Only on balances with
internal calibration masses)

YES = Use Internal calibration mass as
displayed or adjust for accurate Internal
Calibration (see section 13.5.1)
NO = Use external calibration mass

•

Press

[Mode]

to advance to setting of the next menu which is

“PASSCODES” or

[Esc]

to return to normal weighing.

13.5.1 INTERNAL

CALIBRATION MASS ADJUSTMENT

Balance model

Internal Calibration mass (approx.)

PGW 153i

100g

PGW 253i

240g

PGW 453i

240g

PGW 753i

520g

PGW 1502i

1400g

PGW 2502i

1400g

PGW 3502i

1400g

PGW 4502i

1400g

NOTE:

The value of the internal mass is not an exact number, such as 100g.

It must be set by comparing with an external mass. The exact value can be
set, provided this feature is enabled at the factory.

© Adam Equipment Company 2007

Содержание pgw 1502e

















































Результаты поиска

Содержание pgw 1502e

Отзывы:

Похожие инструкции для pgw 1502e

Бренды по названию

Популярные бренды

Adam Equipment pgw 1502e, Руководство пользователя

Результаты поиска

Содержание pgw 1502e

Отзывы:

Похожие инструкции для pgw 1502e

Бренды по названию

Популярные бренды