background image

8

INSTALLATION

HOT WATER CONNECTIONS

Pressure reducing valve

If the mains water pressure is greater than 6 bar, a pressure reducing
valve must be fitted.

Expansion relief valve

The tank expansion relief valve must be ACV approved and
calibrated to a maximum of 7 bar. The valve discharge must be
connected to the drain.

Hot water expansion vessel

We recommend installing a hot water expansion vessel.

Hot water circulation

If the tank is situated a long way from the point of use, then installing
a recirculation loop can provide a faster supply of hot water to the
outlets.

Temperature and pressure relief valve

If using the HeatMaster as an unvented hot water unit, in some
countries, a temperature and pressure relief valve must be fitted -
consult your ACV stockist for assistance.

Example of hot water connection with thermostatic
mixer

1.

Stop cock

2.

Non-return valve

3.

Pressure reducing valve

4.

Expansion relief valve

5.

Hot water expansion vessel

6.

Hot water secondary pump 

(it fitted)

7.

Thermostatic mixing valve

8.

Drawoff tap

9.

Drain cock

10. Stop cock for cleaning
11. Temperature relief valve 

(UK-only)

DANGER!
As a safety measure, we strongly advise
installing a thermostatic mixer to prevent the
risk of burns

Example of h storage connection

Recommended for applications requiring a high peak flow.

Example of series connection

Preferable for high temperature applications with up to three units.

Example of parallel connection

Recommended for applications with a high continuous flow.

1

2

3

4

5

2

6

7

8

9

10

11

I

O

I

O

I

O

I

O

I

O

I

O

I

O

D A N G E R

HOT

Содержание HeatMaster 200 F









Отзывы: