manualshive.com logo in svg

aculab E1, Руководство по установке, Страница: 4 / 31

Поделиться
Скачать
aculab E1 Скачать руководство пользователя страница 4

E1/T1 PCI card installation guide 

4 

1 Introduction 

This introductory section of this document provides a general description of the E1/T1 PCI card, 
it's features and facilities. 

1.1 General 

This document is the installation and user guide for the Aculab E1/T1 PCI card. There are three 
variants of the E1/T1 PCI card, with one (PM1), two (PM2) or four (PM4) Primary Rate Line 
Interfaces (ports) on an interchangeable Line Interface Module (LIM). Up to two optional 
signalling DSP modules can be added when additional resources are needed, for example, to 
support CAS protocols, DTMF and call progress tones, etc.  

 

DSP module A

DSP module B

PM1, 2 or 4

H.100 CT Bus

PCI Bus interface

  

The Aculab E1/T1 PCI card shown with line interface unit (LIM) and optional digital signal processor (DSP) modules 

 

This product is referred to as the ‘E1/T1 PCI card’ in this document unless the context requires a 
more specific term. 

 

The serial number of the E1/T1 PCI card is used when configuring the device driver to uniquely 
identify the E1/T1 PCI card in the system. The serial number of the card is located on the reverse 
of the card (no components) on the top edge and has the format P/N ACXXXX S/N XXXX 
WONXXX. Only the 'number' following S/N is used during driver configuration, the other 
numbers are for Aculab use.  

DSPs 

The above diagram shows optional DSPs fitted to the base card, there are two versions of the 
DSP that may be fitted to the E1/T1 PCI card, the DSP 32 or the DSP 65.  

 

     

 

   

 

DSP32 

    

 

DSP65 

CAUTION 

You may not fit a DSP32 and a DSP65 to the same card. Pre revision 2 PM cards can support one DSP65 or up to two DSP32s. Revision 

2 or later cards can support two DSP32s or two DSP65s. 

Содержание E1
































Отзывы:

Нет отзывов